4. Running the Application

4.1. EAL Command-line Options

The following are the EAL command-line options that can be used in conjunction with the testpmd, or any other DPDK application. See the DPDK Getting Started Guide for more information on these options.

  • -c COREMASK

    Set the hexadecimal bitmask of the cores to run on.

  • -n NUM

    Set the number of memory channels to use.

  • -b, –pci-blacklist domain:bus:devid.func

    Blacklist a PCI devise to prevent EAL from using it. Multiple -b options are allowed.

  • -d LIB.so

    Load an external driver. Multiple -d options are allowed.

  • -w, –pci-whitelist domain:bus:devid:func

    Add a PCI device in white list.

  • -m MB

    Memory to allocate. See also –socket-mem.

  • -r NUM

    Set the number of memory ranks (auto-detected by default).

  • -v

    Display the version information on startup.

  • –xen-dom0

    Support application running on Xen Domain0 without hugetlbfs.

  • –syslog

    Set the syslog facility.

  • –socket-mem

    Set the memory to allocate on specific sockets (use comma separated values).

  • –huge-dir

    Specify the directory where the hugetlbfs is mounted.

  • –proc-type

    Set the type of the current process.

  • –file-prefix

    Prefix for hugepage filenames.

  • -vmware-tsc-map

    Use VMware TSC map instead of native RDTSC.

  • –vdev

    Add a virtual device, with format “<driver><id>[,key=val, ...]”, e.g. –vdev=eth_pcap0,iface=eth2.

  • –base-virtaddr

    Specify base virtual address.

  • –create-uio-dev

    Create /dev/uioX (usually done by hotplug).

  • –no-shconf

    No shared config (mmap’d files).

  • –no-pci

    Disable pci.

  • –no-hpet

    Disable hpet.

  • –no-huge

    Use malloc instead of hugetlbfs.

4.2. Testpmd Command-line Options

The following are the command-line options for the testpmd applications. They must be separated from the EAL options, shown in the previous section, with a – separator:

sudo ./testpmd -c 0xF -n 4 -- -i --portmask=0x1 --nb-cores=2
  • -i, –interactive

    Run testpmd in interactive mode. In this mode, the testpmd starts with a prompt that can be used to start and stop forwarding, configure the application and display stats on the current packet processing session. See the Section 5.0, “Test Runtime Functions” section for more details.

    In non-interactive mode, the application starts with the configuration specified on the command-line and immediately enters forwarding mode.

  • -h, –help

    Display a help message and quit.

  • -a, –auto-start

    Start forwarding on init.

  • –nb-cores=N

    Set the number of forwarding cores, where 1 <= N <= number of cores or RTE_MAX_LCORE from the configuration file. The default value is 1.

  • –nb-ports=N

    Set the number of forwarding ports, where 1 <= N <= number of ports on the board or RTE_MAX_ETHPORTS from the configuration file. The default value is the number of ports on the board.

  • –coremask=0xXX

    Set the hexadecimal bitmask of the cores running the packet forwarding test. The master lcore is reserved for command line parsing only and cannot be masked on for packet forwarding.

  • –portmask=0xXX

    Set the hexadecimal bitmask of the ports used by the packet forwarding test.

  • –numa

    Enable NUMA-aware allocation of RX/TX rings and of RX memory buffers (mbufs).

  • –port-numa-config=(port,socket)[,(port,socket)]

    Specify the socket on which the memory pool to be used by the port will be allocated.

  • –ring-numa-config=(port,flag,socket)[,(port,flag,socket)]

    Specify the socket on which the TX/RX rings for the port will be allocated. Where flag is 1 for RX, 2 for TX, and 3 for RX and TX.

  • –socket-num=N

    Set the socket from which all memory is allocated in NUMA mode, where 0 <= N < number of sockets on the board.

  • –mbuf-size=N

    Set the data size of the mbufs used to N bytes, where N < 65536. The default value is 2048.

  • –total-num-mbufs=N

    Set the number of mbufs to be allocated in the mbuf pools, where N > 1024.

  • –max-pkt-len=N

    Set the maximum packet size to N bytes, where N >= 64. The default value is 1518.

  • –eth-peers-configfile=name

    Use a configuration file containing the Ethernet addresses of the peer ports. The configuration file should contain the Ethernet addresses on separate lines:

    XX:XX:XX:XX:XX:01

    XX:XX:XX:XX:XX:02

    ...

  • –eth-peer=N,XX:XX:XX:XX:XX:XX

    Set the MAC address XX:XX:XX:XX:XX:XX of the peer port N, where 0 <= N < RTE_MAX_ETHPORTS from the configuration file.

  • –pkt-filter-mode=mode

    Set Flow Director mode where mode is either none (the default), signature or perfect. See the Section 5.6, “Flow Director Functions” for more detail.

  • –pkt-filter-report-hash=mode

    Set Flow Director hash match reporting mode where mode is none, match (the default) or always.

  • –pkt-filter-size=N

    Set Flow Director allocated memory size, where N is 64K, 128K or 256K. Sizes are in kilobytes. The default is 64.

  • –pkt-filter-flexbytes-offset=N

    Set the flexbytes offset. The offset is defined in words (not bytes) counted from the first byte of the destination Ethernet MAC address, where N is 0 <= N <= 32. The default value is 0x6.

  • –pkt-filter-drop-queue=N

    Set the drop-queue. In perfect filter mode, when a rule is added with queue = -1, the packet will be enqueued into the RX drop-queue. If the drop-queue does not exist, the packet is dropped. The default value is N=127.

  • –crc-strip

    Enable hardware CRC stripping.

  • –enable-rx-cksum

    Enable hardware RX checksum offload.

  • –disable-hw-vlan

    Disable hardware VLAN.

  • –enable-drop-en

    Enable per-queue packet drop for packets with no descriptors.

  • –disable-rss

    Disable RSS (Receive Side Scaling).

  • –port-topology=mode

    Set port topology, where mode is paired(the default) or chained. In paired mode, the forwarding is between pairs of ports, for example: (0,1), (2,3), (4,5). In chained mode, the forwarding is to the next available port in the port mask, for example: (0,1), (1,2), (2,0). The ordering of the ports can be changed using the portlist testpmd runtime function.

  • –forward-mode=N

    Set forwarding mode. (N: io|mac|mac_retry|mac_swap|flowgen|rxonly|txonly|csum|icmpecho)

  • –rss-ip

    Set RSS functions for IPv4/IPv6 only.

  • –rss-udp

    Set RSS functions for IPv4/IPv6 and UDP.

  • –rxq=N

    Set the number of RX queues per port to N, where 1 <= N <= 65535. The default value is 1.

  • –rxd=N

    Set the number of descriptors in the RX rings to N, where N > 0. The default value is 128.

  • –txq=N

    Set the number of TX queues per port to N, where 1 <= N <= 65535. The default value is 1.

  • –txd=N

    Set the number of descriptors in the TX rings to N, where N > 0. The default value is 512.

  • –burst=N

    Set the number of packets per burst to N, where 1 <= N <= 512. The default value is 16.

  • –mbcache=N

    Set the cache of mbuf memory pools to N, where 0 <= N <= 512. The default value is 16.

  • –rxpt=N

    Set the prefetch threshold register of RX rings to N, where N >= 0. The default value is 8.

  • –rxht=N

    Set the host threshold register of RX rings to N, where N >= 0. The default value is 8.

  • –rxfreet=N

    Set the free threshold of RX descriptors to N, where 0 <= N < value of –rxd. The default value is 0.

  • –rxwt=N

    Set the write-back threshold register of RX rings to N, where N >= 0. The default value is 4.

  • –txpt=N

    Set the prefetch threshold register of TX rings to N, where N >= 0. The default value is 36.

  • –txht=N

    Set the host threshold register of TX rings to N, where N >= 0. The default value is 0.

  • –txwt=N

    Set the write-back threshold register of TX rings to N, where N >= 0. The default value is 0.

  • –txfreet=N

    Set the transmit free threshold of TX rings to N, where 0 <= N <= value of –txd. The default value is 0.

  • –txrst=N

    Set the transmit RS bit threshold of TX rings to N, where 0 <= N <= value of –txd. The default value is 0.

  • –txqflags=0xXXXXXXXX

    Set the hexadecimal bitmask of TX queue flags, where 0 <= N <= 0x7FFFFFFF. The default value is 0.

  • –rx-queue-stats-mapping=(port,queue,mapping)[,(port,queue,mapping)]

    Set the RX queues statistics counters mapping 0 <= mapping <= 15.

  • –tx-queue-stats-mapping=(port,queue,mapping)[,(port,queue,mapping)]

    Set the TX queues statistics counters mapping 0 <= mapping <= 15.

  • –no-flush-rx

    Don’t flush the RX streams before starting forwarding. Used mainly with PCAP drivers.

  • –txpkts=X[,Y]

    Set TX segment sizes.

  • –disable-link-check

    Disable check on link status when starting/stopping ports.

Table Of Contents

Previous topic

3. Compiling the Application

Next topic

5. Testpmd Runtime Functions

This Page