[dpdk-dev] DPDK supported processor

[BYEONG-GI KIM]

Hello.

Hmm, the problem is a little complicated. Actually, I'm trying to use
dpdk-ovs with openstack deployment, but it seems not working correctly.
I've thus been trying to keep track of the primary problem of this.

I've thought my machine's hardware requirements may not be satisfied to
support DPDK, but I think it is solved now.

Best regards

Byeong-Gi KIM


2014-08-21 18:13 GMT+09:00 Masaru Oki <m-oki at stratosphere.co.jp>:

> Hi,
> What is the problem in l3fwd?  link speed?
>
>
> 2014-08-21 18:00 GMT+09:00 BYEONG-GI KIM <kimbyeonggi at gmail.com>:
>
> Thank you for the reply.
>>
>> I tested l3forwarding sample application, and the results were as below:
>>
>> sudo ./build/l3fwd -c 0x0F -n 4 -- -p 0x03
>> --config="(0,0,0),(0,1,1),(1,0,2),(1,1,3)"
>> EAL: Detected lcore 0 as core 0 on socket 0
>> EAL: Detected lcore 1 as core 1 on socket 0
>> EAL: Detected lcore 2 as core 2 on socket 0
>> EAL: Detected lcore 3 as core 3 on socket 0
>> EAL: Detected lcore 4 as core 4 on socket 0
>> EAL: Detected lcore 5 as core 5 on socket 0
>> EAL: Detected lcore 6 as core 6 on socket 0
>> EAL: Detected lcore 7 as core 7 on socket 0
>> EAL: Support maximum 64 logical core(s) by configuration.
>> EAL: Detected 8 lcore(s)
>> EAL: Searching for IVSHMEM devices...
>> EAL: No IVSHMEM configuration found!
>> EAL: Setting up memory...
>> EAL: Ask a virtual area of 0x5ffc00000 bytes
>> EAL: Virtual area found at 0x2aa4aae00000 (size = 0x5ffc00000)
>>
>> EAL: Ask a virtual area of 0x200000 bytes
>> EAL: Virtual area found at 0x7ffff3e00000 (size = 0x200000)
>> EAL: Ask a virtual area of 0x200000 bytes
>> EAL: Virtual area found at 0x7ffff3a00000 (size = 0x200000)
>> EAL: Requesting 12288 pages of size 2MB from socket 0
>> EAL: TSC frequency is ~2399998 KHz
>> EAL: Master core 0 is ready (tid=f7fe9800)
>> EAL: Core 3 is ready (tid=f5998700)
>> EAL: Core 2 is ready (tid=f6199700)
>> EAL: Core 1 is ready (tid=f699a700)
>> EAL: PCI device 0000:00:14.0 on NUMA socket -1
>> EAL:   probe driver: 8086:1f41 rte_igb_pmd
>> EAL:   PCI memory mapped at 0x7ffff7f8d000
>> EAL:   PCI memory mapped at 0x7ffff7f89000
>> EAL: PCI device 0000:00:14.1 on NUMA socket -1
>> EAL:   probe driver: 8086:1f41 rte_igb_pmd
>> EAL:   PCI memory mapped at 0x7ffff7f69000
>> EAL:   PCI memory mapped at 0x7ffff7f65000
>> EAL: PCI device 0000:00:14.2 on NUMA socket -1
>> EAL:   probe driver: 8086:1f41 rte_igb_pmd
>> EAL:   0000:00:14.2 not managed by UIO driver, skipping
>> EAL: PCI device 0000:00:14.3 on NUMA socket -1
>> EAL:   probe driver: 8086:1f41 rte_igb_pmd
>> EAL:   0000:00:14.3 not managed by UIO driver, skipping
>> EAL: PCI device 0000:00:14.2 on NUMA socket -1
>> EAL:   probe driver: 8086:1f41 rte_igb_pmd
>> EAL:   0000:00:14.2 not managed by UIO driver, skipping
>> EAL: PCI device 0000:00:14.3 on NUMA socket -1
>> EAL:   probe driver: 8086:1f41 rte_igb_pmd
>> EAL:   0000:00:14.3 not managed by UIO driver, skipping
>> Initializing port 0 ... Creating queues: nb_rxq=2 nb_txq=4...
>>  Address:0C:C4:7A:05:52:7A, Allocated mbuf pool on socket 0
>> LPM: Adding route 0x01010100 / 24 (0)
>> LPM: Adding route 0x02010100 / 24 (1)
>> LPM: Adding route IPV6 / 48 (0)
>> LPM: Adding route IPV6 / 48 (1)
>> txq=0,0,0 PMD: To improve 1G driver performance, consider setting the TX
>> WTHRESH value to 4, 8, or 16.
>> txq=1,1,0 PMD: To improve 1G driver performance, consider setting the TX
>> WTHRESH value to 4, 8, or 16.
>> txq=2,2,0 PMD: To improve 1G driver performance, consider setting the TX
>> WTHRESH value to 4, 8, or 16.
>> txq=3,3,0 PMD: To improve 1G driver performance, consider setting the TX
>> WTHRESH value to 4, 8, or 16.
>>
>> Initializing port 1 ... Creating queues: nb_rxq=2 nb_txq=4...
>>  Address:0C:C4:7A:05:52:7B, txq=0,0,0 PMD: To improve 1G driver
>> performance, consider setting the TX WTHRESH value to 4, 8, or 16.
>> txq=1,1,0 PMD: To improve 1G driver performance, consider setting the TX
>> WTHRESH value to 4, 8, or 16.
>> txq=2,2,0 PMD: To improve 1G driver performance, consider setting the TX
>> WTHRESH value to 4, 8, or 16.
>> txq=3,3,0 PMD: To improve 1G driver performance, consider setting the TX
>> WTHRESH value to 4, 8, or 16.
>>
>>
>> Initializing rx queues on lcore 0 ... rxq=0,0,0
>> Initializing rx queues on lcore 1 ... rxq=0,1,0
>> Initializing rx queues on lcore 2 ... rxq=1,0,0
>> Initializing rx queues on lcore 3 ... rxq=1,1,0
>>
>> Checking link status.................done
>> Port 0 Link Up - speed 100 Mbps - full-duplex
>> Port 1 Link Up - speed 100 Mbps - full-duplex
>> L3FWD: entering main loop on lcore 1
>> L3FWD: entering main loop on lcore 3
>> L3FWD:  -- lcoreid=1 portid=0 rxqueueid=1
>> L3FWD:  -- lcoreid=3 portid=1 rxqueueid=1
>> L3FWD: entering main loop on lcore 0
>> L3FWD:  -- lcoreid=0 portid=0 rxqueueid=0
>> L3FWD: entering main loop on lcore 2
>> L3FWD:  -- lcoreid=2 portid=1 rxqueueid=0
>>
>> Anyway, I'll also try to test the testpmd application.
>>
>> Best regards
>>
>> Byeong-Gi KIM
>>
>>
>>
>> 2014-08-21 17:56 GMT+09:00 De Lara Guarch, Pablo <
>> pablo.de.lara.guarch at intel.com>:
>>
>> > > -----Original Message-----
>> > > From: dev [mailto:dev-bounces at dpdk.org] On Behalf Of BYEONG-GI KIM
>> > > Sent: Thursday, August 21, 2014 7:04 AM
>> > > To: dev at dpdk.org
>> > > Subject: [dpdk-dev] DPDK supported processor
>> > >
>> > > Hello.
>> > >
>> > > I'm now using Intel Atom processor C2758 on the DPDK testing machines,
>> > but
>> > > it seems not working.
>> > >
>> > > Which sample application would be recommended to test the NIC actually
>> > > works well with DPDK?
>> > >
>> > > Best regards
>> > >
>> > > Byeong-Gi KIM
>> >
>> > Hi,
>> >
>> > Testpmd is the best application you can use for that.
>> >
>> > Best regards,
>> > Pablo
>> >
>>
>
>