[dpdk-dev] [PATCH 1/5] igb_uio: use kernel standard log message
Stephen Hemminger
stephen at networkplumber.org
Wed May 14 18:34:02 CEST 2014
Use pr_info() and dev_info() to print out log messages where appropriate.
Signed-off-by: Stephen Hemminger <shemming at brocade.com>
--- a/lib/librte_eal/linuxapp/igb_uio/igb_uio.c 2014-05-14 09:01:21.149196906 -0700
+++ b/lib/librte_eal/linuxapp/igb_uio/igb_uio.c 2014-05-14 09:01:21.149196906 -0700
@@ -22,6 +22,8 @@
* Intel Corporation
*/
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
#include <linux/device.h>
#include <linux/module.h>
#include <linux/pci.h>
@@ -316,7 +318,7 @@ done:
pci_unlock(pdev);
spin_unlock:
spin_unlock_irqrestore(&udev->lock, flags);
- printk(KERN_INFO "irq 0x%x %s\n", irq, (ret == IRQ_HANDLED) ? "handled" : "not handled");
+ pr_info("irq 0x%x %s\n", irq, (ret == IRQ_HANDLED) ? "handled" : "not handled");
return ret;
}
@@ -479,7 +481,7 @@ igbuio_pci_probe(struct pci_dev *dev, co
* memory
*/
if (pci_enable_device(dev)) {
- printk(KERN_ERR "Cannot enable PCI device\n");
+ dev_err(&dev->dev, "Cannot enable PCI device\n");
goto fail_free;
}
@@ -488,7 +490,7 @@ igbuio_pci_probe(struct pci_dev *dev, co
* module
*/
if (pci_request_regions(dev, "igb_uio")) {
- printk(KERN_ERR "Cannot request regions\n");
+ dev_err(&dev->dev, "Cannot request regions\n");
goto fail_disable;
}
@@ -501,10 +503,10 @@ igbuio_pci_probe(struct pci_dev *dev, co
/* set 64-bit DMA mask */
if (pci_set_dma_mask(dev, DMA_BIT_MASK(64))) {
- printk(KERN_ERR "Cannot set DMA mask\n");
+ dev_err(&dev->dev, "Cannot set DMA mask\n");
goto fail_release_iomem;
} else if (pci_set_consistent_dma_mask(dev, DMA_BIT_MASK(64))) {
- printk(KERN_ERR "Cannot set consistent DMA mask\n");
+ dev_err(&dev->dev, "Cannot set consistent DMA mask\n");
goto fail_release_iomem;
}
@@ -535,7 +537,7 @@ igbuio_pci_probe(struct pci_dev *dev, co
}
else {
pci_disable_msix(udev->pdev);
- printk(KERN_INFO "fail to enable pci msix, or not enough msix entries\n");
+ pr_info("fail to enable pci msix, or not enough msix entries\n");
}
}
switch (udev->mode) {
@@ -563,7 +565,8 @@ igbuio_pci_probe(struct pci_dev *dev, co
if (uio_register_device(&dev->dev, &udev->info))
goto fail_release_iomem;
- printk(KERN_INFO "uio device registered with irq %lx\n", udev->info.irq);
+ dev_info(&dev->dev, "uio device registered with irq %lx\n",
+ udev->info.irq);
return 0;
@@ -587,7 +590,7 @@ igbuio_pci_remove(struct pci_dev *dev)
struct uio_info *info = pci_get_drvdata(dev);
if (info->priv == NULL) {
- printk(KERN_DEBUG "Not igbuio device\n");
+ pr_notice("Not igbuio device\n");
return;
}
@@ -607,18 +610,18 @@ static int
igbuio_config_intr_mode(char *intr_str)
{
if (!intr_str) {
- printk(KERN_INFO "Use MSIX interrupt by default\n");
+ pr_info("Use MSIX interrupt by default\n");
return 0;
}
if (!strcmp(intr_str, "msix")) {
igbuio_intr_mode_preferred = IGBUIO_MSIX_INTR_MODE;
- printk(KERN_INFO "Use MSIX interrupt\n");
+ pr_info("Use MSIX interrupt\n");
} else if (!strcmp(intr_str, "legacy")) {
igbuio_intr_mode_preferred = IGBUIO_LEGACY_INTR_MODE;
- printk(KERN_INFO "Use legacy interrupt\n");
+ pr_info("Use legacy interrupt\n");
} else {
- printk(KERN_INFO "Error: bad parameter - %s\n", intr_str);
+ pr_info("Error: bad parameter - %s\n", intr_str);
return -EINVAL;
}
More information about the dev
mailing list