[dpdk-dev] [PATCH] doc: commands changed in testpmd_funcs for ethertype filter

[Iremonger, Bernard]

> -----Original Message-----
> From: dev [mailto:dev-bounces at dpdk.org] On Behalf Of Jingjing Wu
> Sent: Thursday, January 22, 2015 1:09 AM
> To: dev at dpdk.org
> Subject: [dpdk-dev] [PATCH] doc: commands changed in testpmd_funcs for ethertype filter
> 
> new commands for ethertype filter
>   - ethertype_filter (port_id) (add|del) (mac_addr|mac_ignr)
>     (mac_address) ethertype (ether_type) (drop|fwd) queue (queue_id)
> 
> Signed-off-by: Jingjing Wu <jingjing.wu at intel.com>
> ---
>  doc/guides/testpmd_app_ug/testpmd_funcs.rst | 51 +++++++----------------------
>  1 file changed, 12 insertions(+), 39 deletions(-)
> 
> diff --git a/doc/guides/testpmd_app_ug/testpmd_funcs.rst
> b/doc/guides/testpmd_app_ug/testpmd_funcs.rst
> index be935c2..218835a 100644
> --- a/doc/guides/testpmd_app_ug/testpmd_funcs.rst
> +++ b/doc/guides/testpmd_app_ug/testpmd_funcs.rst
> @@ -1392,61 +1392,34 @@ Filter Functions
> 
>  This section details the available filter functions that are available.
> 
> -add_ethertype_filter
> +ethertype_filter
>  ~~~~~~~~~~~~~~~~~~~~
> 
> -Add a L2 Ethertype filter, which identify packets by their L2 Ethertype mainly assign them to a receive
> queue.
> +Add or delete a L2 Ethertype filter, which identify packets by their L2 Ethertype mainly assign them to
> a receive queue.
> 
> -add_ethertype_filter (port_id) ethertype (eth_value) priority (enable|disable) (pri_value) queue
> (queue_id) index (idx)
> +ethertype_filter (port_id) (add|del) (mac_addr|mac_ignr) (mac_address) ethertype (ether_type)
> (drop|fwd) queue (queue_id)
> 
>  The available information parameters are:
> 
>  *   port_id:  the port which the Ethertype filter assigned on.
> 
> -*   eth_value: the EtherType value want to match,
> -    for example 0x0806 for ARP packet. 0x0800 (IPv4) and 0x86DD (IPv6) are invalid.
> -
> -*   enable: user priority participates in the match.
> -
> -*   disable: user priority doesn't participate in the match.
> -
> -*   pri_value: user priority value that want to match.
> -
> -*   queue_id : The receive queue associated with this EtherType filter
> +*   mac_addr: compare destination mac address.
> 
> -*   index: the index of this EtherType filter
> +*   mac_ignr: ignore destination mac address match.
> 
> -Example:
> -
> -.. code-block:: console
> +*   mac_address: destination mac address to match.
> 
> -    testpmd> add_ethertype_filter 0 ethertype 0x0806 priority disable 0 queue 3 index 0
> -    Assign ARP packet to receive queue 3
> -
> -remove_ethertype_filter
> -~~~~~~~~~~~~~~~~~~~~~~~
> -
> -Remove a L2 Ethertype filter
> -
> -remove_ethertype_filter (port_id) index (idx)
> -
> -get_ethertype_filter
> -~~~~~~~~~~~~~~~~~~~~
> -
> -Get and display a L2 Ethertype filter
> +*   ether_type: the EtherType value want to match,
> +    for example 0x0806 for ARP packet. 0x0800 (IPv4) and 0x86DD (IPv6) are invalid.
> 
> -get_ethertype_filter (port_id) index (idx)
> +*   queue_id : The receive queue associated with this EtherType filter. It is meaningless when
> deleting or dropping.
> 
> -Example:
> +Example, to add/remove an ethertype filter rule:
> 
>  .. code-block:: console
> 
> -    testpmd> get_ethertype_filter 0 index 0
> -
> -    filter[0]:
> -        ethertype: 0x0806
> -        priority: disable, 0
> -        queue: 3
> +    testpmd> ethertype_filter 0 add mac_ignr ethertype 0x0806 fwd queue 3
> +    testpmd> ethertype_filter 0 del mac_ignr ethertype 0x0806 fwd queue 3

Hi Jingjing,

There is a duplicate line here.
I have applied the patch and checked the HTML output (applies and builds cleanly).

Regards,

Bernard
> 
>  add_2tuple_filter
>  ~~~~~~~~~~~~~~~~~
> --
> 1.9.3