[dpdk-dev] [PATCH v3 1/7] lib/librte_ether: modify the structures for fdir new modes

[Lu, Wenzhuo]

Hi Bruce,

> -----Original Message-----
> From: Richardson, Bruce
> Sent: Friday, October 23, 2015 5:58 PM
> To: Lu, Wenzhuo
> Cc: dev at dpdk.org; thomas.monjalon at 6wind.com
> Subject: Re: [dpdk-dev] [PATCH v3 1/7] lib/librte_ether: modify the structures
> for fdir new modes
> 
> On Fri, Oct 23, 2015 at 02:22:28AM +0100, Lu, Wenzhuo wrote:
> > Hi Bruce,
> >
> > > -----Original Message-----
> > > From: Richardson, Bruce
> > > Sent: Thursday, October 22, 2015 8:57 PM
> > > To: Lu, Wenzhuo
> > > Cc: dev at dpdk.org
> > > Subject: Re: [dpdk-dev] [PATCH v3 1/7] lib/librte_ether: modify the
> > > structures for fdir new modes
> > >
> > > On Thu, Oct 22, 2015 at 03:11:36PM +0800, Wenzhuo Lu wrote:
> > > > Define the new modes and modify the filter and mask structures for
> > > > the mac vlan and tunnel modes.
> > > >
> > > > Signed-off-by: Wenzhuo Lu <wenzhuo.lu at intel.com>
> > >
> > > Hi Wenzhuo,
> > >
> > > couple of stylistic comments below, which would help with patch
> > > review, especially with regards to checking for ABI issues.
> > >
> > > /Bruce
> > >
> > > > ---
> > > >  lib/librte_ether/rte_eth_ctrl.h | 69
> > > > ++++++++++++++++++++++++++++++-----------
> > > >  1 file changed, 51 insertions(+), 18 deletions(-)
> > > >
> > > > diff --git a/lib/librte_ether/rte_eth_ctrl.h
> > > > b/lib/librte_ether/rte_eth_ctrl.h index 26b7b33..078faf9 100644
> > > > --- a/lib/librte_ether/rte_eth_ctrl.h
> > > > +++ b/lib/librte_ether/rte_eth_ctrl.h
> > > > @@ -248,6 +248,17 @@ enum rte_eth_tunnel_type {  };
> > > >
> > > >  /**
> > > > + *  Flow Director setting modes: none, signature or perfect.
> > > > + */
> > > > +enum rte_fdir_mode {
> > > > +	RTE_FDIR_MODE_NONE  = 0, /**< Disable FDIR support. */
> > > > +	RTE_FDIR_MODE_SIGNATURE, /**< Enable FDIR signature filter mode.
> > > */
> > > > +	RTE_FDIR_MODE_PERFECT,   /**< Enable FDIR perfect filter mode for
> > > IP. */
> > > > +	RTE_FDIR_MODE_PERFECT_MAC_VLAN, /**< Enable FDIR filter mode
> > > - MAC VLAN. */
> > > > +	RTE_FDIR_MODE_PERFECT_TUNNEL,   /**< Enable FDIR filter mode -
> > > tunnel. */
> > > > +};
> > > > +
> > >
> > > Why is this structure definition moved in the file, it makes seeing
> > > the diff vs the old version difficult.
> > I remember in the original version I move this enum to resolve a compile
> issue.
> > But now after all the code changed, the issue is not here. So, I'll move it
> back.
> >
> > >
> > > > +/**
> > > >   * filter type of tunneling packet
> > > >   */
> > > >  #define ETH_TUNNEL_FILTER_OMAC  0x01 /**< filter by outer MAC
> > > > addr
> > > */
> > > > @@ -377,18 +388,46 @@ struct rte_eth_sctpv6_flow {  };
> > > >
> > > >  /**
> > > > + * A structure used to define the input for MAC VLAN flow  */
> > > > +struct rte_eth_mac_vlan_flow {
> > > > +	struct ether_addr mac_addr;  /**< Mac address to match. */ };
> > > > +
> > > > +/**
> > > > + * Tunnel type for flow director.
> > > > + */
> > > > +enum rte_eth_fdir_tunnel_type {
> > > > +	RTE_FDIR_TUNNEL_TYPE_NVGRE = 0,
> > > > +	RTE_FDIR_TUNNEL_TYPE_VXLAN,
> > > > +	RTE_FDIR_TUNNEL_TYPE_UNKNOWN,
> > > > +};
> > > > +
> > > > +/**
> > > > + * A structure used to define the input for tunnel flow, now it's
> > > > +VxLAN or
> > > > + * NVGRE
> > > > + */
> > > > +struct rte_eth_tunnel_flow {
> > > > +	enum rte_eth_fdir_tunnel_type tunnel_type; /**< Tunnel type to
> > > match. */
> > > > +	uint32_t tunnel_id;                        /**< Tunnel ID to match. TNI, VNI...
> > > */
> > > > +	struct ether_addr mac_addr;                /**< Mac address to match. */
> > > > +};
> > > > +
> > > > +/**
> > > >   * An union contains the inputs for all types of flow
> > > >   */
> > > >  union rte_eth_fdir_flow {
> > > > -	struct rte_eth_l2_flow     l2_flow;
> > > > -	struct rte_eth_udpv4_flow  udp4_flow;
> > > > -	struct rte_eth_tcpv4_flow  tcp4_flow;
> > > > -	struct rte_eth_sctpv4_flow sctp4_flow;
> > > > -	struct rte_eth_ipv4_flow   ip4_flow;
> > > > -	struct rte_eth_udpv6_flow  udp6_flow;
> > > > -	struct rte_eth_tcpv6_flow  tcp6_flow;
> > > > -	struct rte_eth_sctpv6_flow sctp6_flow;
> > > > -	struct rte_eth_ipv6_flow   ipv6_flow;
> > > > +	struct rte_eth_l2_flow         l2_flow;
> > > > +	struct rte_eth_udpv4_flow      udp4_flow;
> > > > +	struct rte_eth_tcpv4_flow      tcp4_flow;
> > > > +	struct rte_eth_sctpv4_flow     sctp4_flow;
> > > > +	struct rte_eth_ipv4_flow       ip4_flow;
> > > > +	struct rte_eth_udpv6_flow      udp6_flow;
> > > > +	struct rte_eth_tcpv6_flow      tcp6_flow;
> > > > +	struct rte_eth_sctpv6_flow     sctp6_flow;
> > > > +	struct rte_eth_ipv6_flow       ipv6_flow;
> > > > +	struct rte_eth_mac_vlan_flow   mac_vlan_flow;
> > > > +	struct rte_eth_tunnel_flow     tunnel_flow;
> > >
> > > Can you please minimize the whitespace changes here. It looks in the
> > > diff like you are replacing the entire set of entries, but on closer
> > > inspection it looks like you are just adding in two extra lines.
> > Using vi or other editing tools, we can see all this fields are
> > aligned. I think it's worth to keep it.
> >
> 
> I'm a bit uncertain about this. It really makes the diff confusing, so ideally
> the whitespace cleanup should go in a separate patch. On the other hand,
> it's a fairly small change, so maybe it's ok here.
> 
> Right now, I'd prefer it as a separate patch, because I had to manually go
> through each line added/removed to see how they tallied before I
> understood that you were just adding in two new lines, and nothing else.
> 
> Thomas, perhaps you'd like to comment here?
Maybe you miss the Thomas' mail. 
I'd like to remove the whitespaces for reviewer's sake. :) 
> 
> > >
> > > >  };
> > > >
> > > >  /**
> > > > @@ -465,6 +504,9 @@ struct rte_eth_fdir_masks {
> > > >  	struct rte_eth_ipv6_flow   ipv6_mask;
> > > >  	uint16_t src_port_mask;
> > > >  	uint16_t dst_port_mask;
> > > > +	uint8_t mac_addr_byte_mask;  /** Per byte MAC address mask */
> > > > +	uint32_t tunnel_id_mask;  /** tunnel ID mask */
> > > > +	uint8_t tunnel_type_mask;
> > > >  };
> > > >
> > > >  /**
> > > > @@ -515,15 +557,6 @@ struct rte_eth_fdir_flex_conf {
> > > >  	/**< Flex mask configuration for each flow type */  };
> > > >
> > > > -/**
> > > > - *  Flow Director setting modes: none, signature or perfect.
> > > > - */
> > > > -enum rte_fdir_mode {
> > > > -	RTE_FDIR_MODE_NONE      = 0, /**< Disable FDIR support. */
> > > > -	RTE_FDIR_MODE_SIGNATURE,     /**< Enable FDIR signature filter
> > > mode. */
> > > > -	RTE_FDIR_MODE_PERFECT,       /**< Enable FDIR perfect filter mode.
> > > */
> > > > -};
> > > > -
> > > >  #define UINT32_BIT (CHAR_BIT * sizeof(uint32_t))  #define
> > > > RTE_FLOW_MASK_ARRAY_SIZE \
> > > >  	(RTE_ALIGN(RTE_ETH_FLOW_MAX, UINT32_BIT)/UINT32_BIT)
> > > > --
> > > > 1.9.3
> > > >