[dpdk-dev] Port 0 Link Down - L2fwd sample application

[Lu, Wenzhuo]

Hi Vivek,


> -----Original Message-----
> From: dev [mailto:dev-bounces at dpdk.org] On Behalf Of Vivek Gupta
> Sent: Thursday, April 7, 2016 9:19 PM
> To: Marc Sune
> Cc: dev at dpdk.org
> Subject: Re: [dpdk-dev] Port 0 Link Down - L2fwd sample application
> 
> I have installed DPDK 2.2 version and didn’t build source coe.
The info is too limited, I cannot figure out what you're doing.
1, Confused, you didn't build the source code, so how you install DPDK?
2, Don't know the topology. Please make sure the connection is ready.
3, Would you like to try igb_uio? Normally we're using this one.

> 
> From: Marc Sune [mailto:marcdevel at gmail.com]
> Sent: Thursday, April 07, 2016 6:27 PM
> To: Vivek Gupta <vivek-g at hcl.com>
> Cc: dev at dpdk.org
> Subject: Re: [dpdk-dev] Port 0 Link Down - L2fwd sample application
> 
> 
> 
> 2016-04-07 14:50 GMT+02:00 Vivek Gupta <vivek-g at hcl.com<mailto:vivek-
> g at hcl.com>>:
> Hi
> 
> I have binded eth0 and eth1 with DPDK and then tried to run the l2fwd example
> as below
> 
> ./build/l2fwd -c f -n 4 -- -q 8 -p 0x11  but each time I get error
> *****************************
> Checking link status..............
> Port 0 Link Down
> Port 1 Link Down
> ********************************************
> 
> I tried with test-pmd example but same result.Could you please help to up the
> link?
> 
> Port status is as below-
> Network devices using DPDK-compatible driver
> ============================================
> 0000:01:00.0 'Ethernet Controller 10-Gigabit X540-AT2' drv=uio_pci_generic
> unused=igb_uio
> 0000:01:00.1 'Ethernet Controller 10-Gigabit X540-AT2' drv=uio_pci_generic
> unused=igb_uio
> 0000:06:00.0 'Ethernet Controller 10-Gigabit X540-AT2' drv=uio_pci_generic
> unused=igb_uio
> 0000:06:00.1 'Ethernet Controller 10-Gigabit X540-AT2' drv=uio_pci_generic
> unused=igb_uio
> 
> Network devices using kernel driver
> ===================================
> 0000:81:00.0 'Ethernet Controller 10-Gigabit X540-AT2' if=eth4 drv=ixgbe
> unused=igb_uio,uio_pci_generic
> 0000:81:00.1 'Ethernet Controller 10-Gigabit X540-AT2' if=eth5 drv=ixgbe
> unused=igb_uio,uio_pci_generic
> 
> Other network devices
> =====================
> <none>
> 
> 
> Thanks & Regards
> Vivek Gupta
> 
> In which commit or version are you?
> 
> Marc
> 
> 
> 
> ::DISCLAIMER::
> --------------------------------------------------------------------------------------------------
> --------------------------------------------------
> 
> The contents of this e-mail and any attachment(s) are confidential and intended
> for the named recipient(s) only.
> E-mail transmission is not guaranteed to be secure or error-free as information
> could be intercepted, corrupted, lost, destroyed, arrive late or incomplete, or
> may contain viruses in transmission. The e mail and its contents (with or without
> referred errors) shall therefore not attach any liability on the originator or HCL
> or its affiliates.
> Views or opinions, if any, presented in this email are solely those of the author
> and may not necessarily reflect the views or opinions of HCL or its affiliates. Any
> form of reproduction, dissemination, copying, disclosure, modification,
> distribution and / or publication of this message without the prior written
> consent of authorized representative of HCL is strictly prohibited. If you have
> received this email in error please delete it and notify the sender immediately.
> Before opening any email and/or attachments, please check them for viruses
> and other defects.
> 
> --------------------------------------------------------------------------------------------------
> --------------------------------------------------