[dpdk-dev] igb_uio binding issue

[De Lara Guarch, Pablo]

Hi Pankaj,

> -----Original Message-----
> From: dev [mailto:dev-bounces at dpdk.org] On Behalf Of Pankaj Joshi
> Sent: Monday, February 01, 2016 11:59 AM
> To: dev at dpdk.org
> Subject: [dpdk-dev] igb_uio binding issue
> 
> Hello,
> 
> I am running DPDK sample application of l2_fwd.
> I have some of the ports like ,
> 
> Network devices using IGB_UIO driver
> ====================================
> 0000:84:00.0 'I350 Gigabit Network Connection' drv=igb_uio unused=
> 0000:84:00.1 'I350 Gigabit Network Connection' drv=igb_uio unused=
> Network devices using kernel driver
> ===================================
> 0000:05:00.0 'I350 Gigabit Network Connection' if=eth0 drv=igb
> unused=igb_uio *Active*
> 0000:05:00.1 'I350 Gigabit Network Connection' if=eth1 drv=igb
> unused=igb_uio
> 0000:06:00.0 '82599ES 10-Gigabit SFI/SFP+ Network Connection' if=eth4
> drv=ixgbe unused=igb_uio
> 0000:06:00.1 '82599ES 10-Gigabit SFI/SFP+ Network Connection' if=eth5
> drv=ixgbe unused=igb_uio
> 0000:0c:00.0 '82599ES 10-Gigabit SFI/SFP+ Network Connection' if=eth6
> drv=ixgbe unused=igb_uio
> 0000:0c:00.1 '82599ES 10-Gigabit SFI/SFP+ Network Connection' if=eth7
> drv=ixgbe unused=igb_uio
> Other network devices
> =====================
> <none>
> 
> I have binded two port, but while running application it is searching for
> ports which I have not binded.. Logs are showing as below :
> 
> EAL: Core 1 is ready (tid=cef5c700)
> EAL: PCI device 0000:05:00.0 on NUMA socket 0
> EAL:   probe driver: 8086:1521 rte_igb_pmd
> EAL:   0000:05:00.0 not managed by UIO driver, skipping
> EAL: PCI device 0000:05:00.1 on NUMA socket 0
> EAL:   probe driver: 8086:1521 rte_igb_pmd
> EAL:   0000:05:00.1 not managed by UIO driver, skipping
> EAL: PCI device 0000:84:00.0 on NUMA socket 1
> EAL:   probe driver: 8086:1521 rte_igb_pmd
> EAL:   PCI memory mapped at 0x7f49d021a000
> EAL:   PCI memory mapped at 0x7f49d0354000
> EAL: PCI device 0000:84:00.1 on NUMA socket 1
> EAL:   probe driver: 8086:1521 rte_igb_pmd
> EAL:   PCI memory mapped at 0x7f49cd65a000
> EAL:   PCI memory mapped at 0x7f49d0216000
> Lcore 0: RX port 0
> Lcore 1: RX port 1
> Initializing port 0... EAL: Error - exiting with code: 1
>   Cause: rte_eth_rx_queue_setup:err=-12, port=0
> 
> Can any one figure out the problem.
> 
As you can see in the log, DPDK got the ports that you bound to igb_uio, 84:00.x (the others have been skipped).
The problem is that it could not configure the devices properly.
Could you send the command line that you used?

Pablo
> thanks,
> 
> Pankaj Joshi