[dpdk-dev] [PATCH v2] i40e: add VEB switching support for i40e

[Zhe Tao]

Signed-off-by: Zhe Tao <zhe.tao at intel.com>

VEB switching feature for i40e is used to enable the switching between the
 VSIs connect to the virtual bridge. The old implementation is setting the
 virtual bridge mode as VEPA which is port aggregation. Enable the switching
 ability by setting the loop back mode for the specific VSIs which connect to PF
 or VFs.

v1: Add the VEB switching support.
v2: Add the check for the FW version,which should larger than 5.0.
    Add release note.
---
 doc/guides/rel_notes/release_16_04.rst |  1 +
 drivers/net/i40e/i40e_ethdev.c         | 57 +++++++++++++++++++++++++++++-----
 2 files changed, 50 insertions(+), 8 deletions(-)

diff --git a/doc/guides/rel_notes/release_16_04.rst b/doc/guides/rel_notes/release_16_04.rst
index 5786f74..eb7effc 100644
--- a/doc/guides/rel_notes/release_16_04.rst
+++ b/doc/guides/rel_notes/release_16_04.rst
@@ -46,6 +46,7 @@ This section should contain new features added in this release. Sample format:
 
 * **Added vhost-user live migration support.**
 
+* **Added VEB switching support for FVL.**
 
 Resolved Issues
 ---------------
diff --git a/drivers/net/i40e/i40e_ethdev.c b/drivers/net/i40e/i40e_ethdev.c
index ef24122..5527cb1 100644
--- a/drivers/net/i40e/i40e_ethdev.c
+++ b/drivers/net/i40e/i40e_ethdev.c
@@ -3822,6 +3822,45 @@ i40e_vsi_get_bw_config(struct i40e_vsi *vsi)
 	return I40E_SUCCESS;
 }
 
+/* i40e_enable_pf_lb
+ * @pf: pointer to the pf structure
+ *
+ * allow loopback on pf
+ */
+static inline void
+i40e_enable_pf_lb(struct i40e_pf *pf)
+{
+	struct i40e_hw *hw = I40E_PF_TO_HW(pf);
+	struct i40e_vsi_context ctxt;
+	int ret;
+
+	/* Use the FW API if FW >= v5.0 */
+	if (hw->aq.fw_maj_ver < 5) {
+		PMD_INIT_LOG(ERR, "FW < v5.0, cannot enable loopback");
+		return;
+	}
+
+	memset(&ctxt, 0, sizeof(ctxt));
+	ctxt.seid = pf->main_vsi_seid;
+	ctxt.pf_num = hw->pf_id;
+	ret = i40e_aq_get_vsi_params(hw, &ctxt, NULL);
+	if (ret) {
+		PMD_DRV_LOG(ERR, "cannot get pf vsi config, err %d, aq_err %d",
+			    ret, hw->aq.asq_last_status);
+		return;
+	}
+	ctxt.flags = I40E_AQ_VSI_TYPE_PF;
+	ctxt.info.valid_sections =
+		rte_cpu_to_le_16(I40E_AQ_VSI_PROP_SWITCH_VALID);
+	ctxt.info.switch_id |=
+		rte_cpu_to_le_16(I40E_AQ_VSI_SW_ID_FLAG_ALLOW_LB);
+
+	ret = i40e_aq_update_vsi_params(hw, &ctxt, NULL);
+	if (ret)
+		PMD_DRV_LOG(ERR, "update vsi switch failed, aq_err=%d\n",
+			    hw->aq.asq_last_status);
+}
+
 /* Setup a VSI */
 struct i40e_vsi *
 i40e_vsi_setup(struct i40e_pf *pf,
@@ -3857,6 +3896,8 @@ i40e_vsi_setup(struct i40e_pf *pf,
 			PMD_DRV_LOG(ERR, "VEB setup failed");
 			return NULL;
 		}
+		/* set ALLOWLOOPBACk on pf, when veb is created */
+		i40e_enable_pf_lb(pf);
 	}
 
 	vsi = rte_zmalloc("i40e_vsi", sizeof(struct i40e_vsi), 0);
@@ -4029,14 +4070,14 @@ i40e_vsi_setup(struct i40e_pf *pf,
 		ctxt.connection_type = 0x1;
 		ctxt.flags = I40E_AQ_VSI_TYPE_VF;
 
-		/**
-		 * Do not configure switch ID to enable VEB switch by
-		 * I40E_AQ_VSI_SW_ID_FLAG_ALLOW_LB. Because in Fortville,
-		 * if the source mac address of packet sent from VF is not
-		 * listed in the VEB's mac table, the VEB will switch the
-		 * packet back to the VF. Need to enable it when HW issue
-		 * is fixed.
-		 */
+		/* Use the VEB configuration if FW >= v5.0 */
+		if (hw->aq.fw_maj_ver >= 5) {
+			/* Configure switch ID */
+			ctxt.info.valid_sections |=
+			rte_cpu_to_le_16(I40E_AQ_VSI_PROP_SWITCH_VALID);
+			ctxt.info.switch_id =
+			rte_cpu_to_le_16(I40E_AQ_VSI_SW_ID_FLAG_ALLOW_LB);
+		}
 
 		/* Configure port/vlan */
 		ctxt.info.valid_sections |=
-- 
2.1.4