[dpdk-dev] [PATCH v2 1/2] doc: fix framework of ixgbe doc
Wenzhuo Lu
wenzhuo.lu at intel.com
Thu Feb 9 02:27:59 CET 2017
The framework of the ixgbe doc is not appropriate,
adjust it.
Fixes: 972e365bfe7a ("doc: nics guide")
CC: stable at dpdk.org
Signed-off-by: Wenzhuo Lu <wenzhuo.lu at intel.com>
---
doc/guides/nics/ixgbe.rst | 19 +++++++++++--------
1 file changed, 11 insertions(+), 8 deletions(-)
diff --git a/doc/guides/nics/ixgbe.rst b/doc/guides/nics/ixgbe.rst
index 3b6851b..05ecc2a 100644
--- a/doc/guides/nics/ixgbe.rst
+++ b/doc/guides/nics/ixgbe.rst
@@ -129,7 +129,7 @@ The tx_rs_thresh value must be greater than or equal to RTE_PMD_IXGBE_TX_MAX_BUR
but less or equal to RTE_IXGBE_TX_MAX_FREE_BUF_SZ.
Consequently, by default the tx_rs_thresh value is in the range 32 to 64.
-Feature not Supported by RX Vector PMD
+Feature not Supported by TX Vector PMD
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
TX vPMD only works when txq_flags is set to IXGBE_SIMPLE_FLAGS.
@@ -148,16 +148,16 @@ The following MACROs are used for these three features:
* ETH_TXQ_FLAGS_NOXSUMTCP
Application Programming Interface
-~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+---------------------------------
In DPDK release v16.11 an API for ixgbe specific functions has been added to the ixgbe PMD.
The declarations for the API functions are in the header ``rte_pmd_ixgbe.h``.
Sample Application Notes
-~~~~~~~~~~~~~~~~~~~~~~~~
+------------------------
testpmd
-^^^^^^^
+~~~~~~~
By default, using CONFIG_RTE_IXGBE_RX_OLFLAGS_ENABLE=y:
@@ -172,21 +172,24 @@ When CONFIG_RTE_IXGBE_RX_OLFLAGS_ENABLE=n, better performance can be achieved:
./x86_64-native-linuxapp-gcc/app/testpmd -c 300 -n 4 -- -i --burst=32 --rxfreet=32 --mbcache=250 --txpt=32 --rxht=8 --rxwt=0 --txfreet=32 --txrst=32 --txqflags=0xf01 --disable-hw-vlan
l3fwd
-^^^^^
+~~~~~
When running l3fwd with vPMD, there is one thing to note.
In the configuration, ensure that port_conf.rxmode.hw_ip_checksum=0.
Otherwise, by default, RX vPMD is disabled.
load_balancer
-^^^^^^^^^^^^^
+~~~~~~~~~~~~~
As in the case of l3fwd, set configure port_conf.rxmode.hw_ip_checksum=0 to enable vPMD.
In addition, for improved performance, use -bsz "(32,32),(64,64),(32,32)" in load_balancer to avoid using the default burst size of 144.
+Limitations or Known issues
+---------------------------
+
Malicious Driver Detection not Supported
-----------------------------------------
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
The Intel x550 series NICs support a feature called MDD (Malicious
Driver Detection) which checks the behavior of the VF driver.
@@ -207,7 +210,7 @@ it by default.)
Statistics
-----------
+~~~~~~~~~~
The statistics of ixgbe hardware must be polled regularly in order for it to
remain consistent. Running a DPDK application without polling the statistics will
--
1.9.3
More information about the dev
mailing list