[dpdk-dev] [PATCH] net/ixgbe: ensure link status is updated

[Dai, Wei]

> -----Original Message-----
> From: Olivier MATZ [mailto:olivier.matz at 6wind.com]
> Sent: Thursday, February 9, 2017 1:03 AM
> To: Dai, Wei <wei.dai at intel.com>
> Cc: Laurent Hardy <laurent.hardy at 6wind.com>; Zhang, Helin
> <helin.zhang at intel.com>; Ananyev, Konstantin
> <konstantin.ananyev at intel.com>; dev at dpdk.org
> Subject: Re: [dpdk-dev] [PATCH] net/ixgbe: ensure link status is updated
> 
> Hi Wei,
> 
> On Wed, 8 Feb 2017 15:51:42 +0000, "Dai, Wei" <wei.dai at intel.com> wrote:
> > > -----Original Message-----
> > > From: dev [mailto:dev-bounces at dpdk.org] On Behalf Of Laurent Hardy
> > > Sent: Friday, November 18, 2016 1:30 AM
> > > To: Zhang, Helin <helin.zhang at intel.com>; Ananyev, Konstantin
> > > <konstantin.ananyev at intel.com>
> > > Cc: dev at dpdk.org
> > > Subject: [dpdk-dev] [PATCH] net/ixgbe: ensure link status is updated
> > >
> > > In case of link speed set to 1Gb at peer side (with autoneg or with
> > > defined speed) and cable not plugged-in when device is configured
> > > and started, then link status is not updated properly with new speed
> > > as no link setup is triggered.
> > >
> > > To avoid this issue, IXGBE_FLAG_NEED_LINK_CONFIG is set to try a
> > > link setup each time link_update() is triggered and current link
> > > status is down. When cable is plugged-in, link setup will be
> > > performed via ixgbe_setup_link().
> > >
> > > Signed-off-by: Laurent Hardy <laurent.hardy at 6wind.com>
> > > ---
> > >  drivers/net/ixgbe/ixgbe_ethdev.c |   20 ++++++++++++++++++++
> > >  drivers/net/ixgbe/ixgbe_ethdev.h |    1 +
> > >  2 files changed, 21 insertions(+)
> > >
> > > diff --git a/drivers/net/ixgbe/ixgbe_ethdev.c
> > > b/drivers/net/ixgbe/ixgbe_ethdev.c
> > > index 52ebbe4..513d1d5 100644
> > > --- a/drivers/net/ixgbe/ixgbe_ethdev.c
> > > +++ b/drivers/net/ixgbe/ixgbe_ethdev.c
> > > @@ -2095,6 +2095,7 @@ ixgbe_dev_configure(struct rte_eth_dev *dev)
> > >
> > >  	/* set flag to update link status after init */
> > >  	intr->flags |= IXGBE_FLAG_NEED_LINK_UPDATE;
> > > +	intr->flags |= IXGBE_FLAG_NEED_LINK_CONFIG;
> > >
> > >  	/*
> > >  	 * Initialize to TRUE. If any of Rx queues doesn't meet the bulk
> > > @@ -3117,8 +3118,12 @@ ixgbe_dev_link_update(struct rte_eth_dev
> > > *dev, int wait_to_complete)
> > >  	struct ixgbe_hw *hw =
> > > IXGBE_DEV_PRIVATE_TO_HW(dev->data->dev_private);
> > >  	struct rte_eth_link link, old;
> > >  	ixgbe_link_speed link_speed = IXGBE_LINK_SPEED_UNKNOWN;
> > > +	struct ixgbe_interrupt *intr =
> > > +		IXGBE_DEV_PRIVATE_TO_INTR(dev->data->dev_private);
> > >  	int link_up;
> > >  	int diag;
> > > +	u32 speed = 0;
> > > +	bool autoneg = false;
> > >
> > >  	link.link_status = ETH_LINK_DOWN;
> > >  	link.link_speed = 0;
> > > @@ -3128,6 +3133,19 @@ ixgbe_dev_link_update(struct rte_eth_dev
> > > *dev, int wait_to_complete)
> > >
> > >  	hw->mac.get_link_status = true;
> > >
> > > +	if (intr->flags & IXGBE_FLAG_NEED_LINK_CONFIG) {
> > > +		speed = hw->phy.autoneg_advertised;
> > > +		if (!speed) {
> > > +			ixgbe_get_link_capabilities(hw, &speed,
> > > &autoneg);
> > > +			/* setup the highest link when no autoneg
> > > */
> > > +			if (!autoneg) {
> > > +				if (speed &
> > > IXGBE_LINK_SPEED_10GB_FULL)
> > > +					speed =
> > > IXGBE_LINK_SPEED_10GB_FULL;
> > > +			}
> > > +		}
> > > +		ixgbe_setup_link(hw, speed, true);
> > > +	}
> > > +
> > >  	/* check if it needs to wait to complete, if lsc interrupt is
> > > enabled */ if (wait_to_complete == 0 ||
> > > dev->data->dev_conf.intr_conf.lsc != 0) diag = ixgbe_check_link(hw,
> > > &link_speed, &link_up, 0); @@ -3145,10 +3163,12 @@
> > > ixgbe_dev_link_update(struct rte_eth_dev *dev, int wait_to_complete)
> > >
> > >  	if (link_up == 0) {
> > >  		rte_ixgbe_dev_atomic_write_link_status(dev, &link);
> > > +		intr->flags |= IXGBE_FLAG_NEED_LINK_CONFIG;
> > >  		if (link.link_status == old.link_status)
> > >  			return -1;
> > >  		return 0;
> > >  	}
> > > +	intr->flags &= ~IXGBE_FLAG_NEED_LINK_CONFIG;
> > >  	link.link_status = ETH_LINK_UP;
> > >  	link.link_duplex = ETH_LINK_FULL_DUPLEX;
> > >
> > > diff --git a/drivers/net/ixgbe/ixgbe_ethdev.h
> > > b/drivers/net/ixgbe/ixgbe_ethdev.h
> > > index e060c3d..9d335ba 100644
> > > --- a/drivers/net/ixgbe/ixgbe_ethdev.h
> > > +++ b/drivers/net/ixgbe/ixgbe_ethdev.h
> > > @@ -43,6 +43,7 @@
> > >  #define IXGBE_FLAG_NEED_LINK_UPDATE (uint32_t)(1 << 0)
> > >  #define IXGBE_FLAG_MAILBOX          (uint32_t)(1 << 1)
> > >  #define IXGBE_FLAG_PHY_INTERRUPT    (uint32_t)(1 << 2)
> > > +#define IXGBE_FLAG_NEED_LINK_CONFIG (uint32_t)(1 << 3)
> >
> > Now there is following macro in DPDK 17.02-rc2.
> > #define IXGBE_FLAG_MACSEC           (uint32_t)(1 << 3)
> > You can redefine it as #define IXGBE_FLAG_NEED_LINK_CONFIG
> > (uint32_t)(1 << 4)
> 
> Thanks, I'll send a v2.
> 
> Do you agree with the rest of the patch?
So far I have no disagree opinions about the reset of this patch.
> 
> 
> Regards,
> Olivier