[dpdk-dev] [PATCH] doc: update failsafe feature list

[Matan Azrad]

Hi Ferruh

> -----Original Message-----
> From: Ferruh Yigit [mailto:ferruh.yigit at intel.com]
> Sent: Tuesday, September 19, 2017 2:00 PM
> To: Matan Azrad <matan at mellanox.com>; Gaetan Rivet
> <gaetan.rivet at 6wind.com>
> Cc: dev at dpdk.org; john.mcnamara at intel.com
> Subject: Re: [dpdk-dev] [PATCH] doc: update failsafe feature list
> 
> On 9/19/2017 11:04 AM, Matan Azrad wrote:
> >
> > Hi Ferruh
> >
> >> -----Original Message-----
> >> From: Ferruh Yigit [mailto:ferruh.yigit at intel.com]
> >> Sent: Tuesday, September 19, 2017 12:27 PM
> >> To: Matan Azrad <matan at mellanox.com>; Gaetan Rivet
> >> <gaetan.rivet at 6wind.com>
> >> Cc: dev at dpdk.org
> >> Subject: Re: [dpdk-dev] [PATCH] doc: update failsafe feature list
> >>
> >> On 9/14/2017 4:32 PM, Matan Azrad wrote:
> >>> Add supported failsafe features to feature list.
> >>> Remove stats per queue feature from failsafe feature list since
> >>> queue_stats_mapping_set dev op has not implemented yet.
> >>>
> >>> Signed-off-by: Matan Azrad <matan at mellanox.com>
> >>> ---
> >>>  doc/guides/nics/features/failsafe.ini | 15 ++++++++++++++-
> >>>  1 file changed, 14 insertions(+), 1 deletion(-)
> >>>
> >>> diff --git a/doc/guides/nics/features/failsafe.ini
> >>> b/doc/guides/nics/features/failsafe.ini
> >>> index a42e344..9f48455 100644
> >>> --- a/doc/guides/nics/features/failsafe.ini
> >>> +++ b/doc/guides/nics/features/failsafe.ini
> >>> @@ -4,20 +4,33 @@
> >>>  ; Refer to default.ini for the full list of available PMD features.
> >>>  ;
> >>>  [Features]
> >>> +Speed capabilities   = Y
> >>>  Link status          = Y
> >>>  Link status event    = Y
> >>>  MTU update           = Y
> >>>  Jumbo frame          = Y
> >>> +Scattered Rx         = Y
> >>> +LRO                  = Y
> >>> +TSO                  = Y
> >>>  Promiscuous mode     = Y
> >>>  Allmulticast mode    = Y
> >>>  Unicast MAC filter   = Y
> >>>  Multicast MAC filter = Y
> >>>  VLAN filter          = Y
> >>> +Ethertype filter     = Y
> >>> +N-tuple filter       = Y
> >>> +SYN filter           = Y
> >>> +Tunnel filter        = Y
> >>> +Flexible filter      = Y
> >>> +Hash filter          = Y
> >>> +Flow director        = Y
> >>>  Flow control         = Y
> >>>  Flow API             = Y
> >>> +QinQ offload         = Y
> >>> +L3 checksum offload  = Y
> >>> +L4 checksum offload  = Y
> >>>  Packet type parsing  = Y
> >>>  Basic stats          = Y
> >>> -Stats per queue      = Y
> >>>  ARMv7                = Y
> >>>  ARMv8                = Y
> >>>  Power8               = Y
> >>
> >> I am not sure if claiming support for these features is correct.
> >> Failsafe itself doesn't provide these features, but relies underlying
> >> hardware which we don't really know what they supports or not in this
> stage.
> >>
> >
> > Don't you think that almost all failsafe features rely underlying hardware or
> sub PMDs?
> 
> You are right, perhaps we should remove all. This is helpful to show what
> device features are supported. For failsafe, is this information useful?
> 
Since there are features that failsafe cannot support without any sub PMD dependences
(for example "Stats per queue") it is useful.

> >
> >> OK for dropping "Stats per queue"
> >>
> >>>
> >