[dpdk-dev] [PATCH v5 0/3] runtime queue setup

[Ananyev, Konstantin]

> -----Original Message-----
> From: Zhang, Qi Z
> Sent: Monday, April 2, 2018 4:00 AM
> To: thomas at monjalon.net; Ananyev, Konstantin <konstantin.ananyev at intel.com>
> Cc: dev at dpdk.org; Xing, Beilei <beilei.xing at intel.com>; Wu, Jingjing <jingjing.wu at intel.com>; Lu, Wenzhuo <wenzhuo.lu at intel.com>;
> Zhang, Qi Z <qi.z.zhang at intel.com>
> Subject: [PATCH v5 0/3] runtime queue setup
> 
> v5:
> - fix first tx queue check in i40e.
> 
> v4:
> - fix i40e rx/tx funciton conflict handle.
> - no need conflict check for first rx/tx queue at runtime setup.
> - fix missing offload paramter in testpmd cmdline.
> 
> v3:
> - not overload deferred start.
> - rename deferred setup to runtime setup.
> - remove unecessary testpmd parameters (patch 2/4 of v2)
> - add offload support to testpmd queue setup command line
> - i40e fix: return fail when required rx/tx function conflict with
>   exist setup.
> 
> v2:
> - enhance comment in rte_ethdev.h
> 
> According to exist implementation,rte_eth_[rx|tx]_queue_setup will
> always return fail if device is already started(rte_eth_dev_start).
> 
> This can't satisfied the usage when application want to deferred setup
> part of the queues while keep traffic running on those queues already
> be setup.
> 
> example:
> rte_eth_dev_config(nb_rxq = 2, nb_txq =2)
> rte_eth_rx_queue_setup(idx = 0 ...)
> rte_eth_rx_queue_setup(idx = 0 ...)
> rte_eth_dev_start(...) /* [rx|tx]_burst is ready to start on queue 0 */
> rte_eth_rx_queue_setup(idx=1 ...) /* fail*/
> 
> Basically this is not a general hardware limitation, because for NIC
> like i40e, ixgbe, it is not necessary to stop the whole device before
> configure a fresh queue or reconfigure an exist queue with no traffic
> on it.
> 
> The patch let etherdev driver expose the capability flag through
> rte_eth_dev_info_get when it support deferred queue configuraiton,
> then base on these flag, rte_eth_[rx|tx]_queue_setup could decide
> continue to setup the queue or just return fail when device already
> started.
> 
> 
> Qi Zhang (3):
>   ether: support runtime queue setup
>   app/testpmd: add command for queue setup
>   net/i40e: enable runtime queue setup
> 
>  app/test-pmd/cmdline.c                      | 129 ++++++++++++++++++++
>  doc/guides/nics/features.rst                |   8 ++
>  doc/guides/testpmd_app_ug/testpmd_funcs.rst |   7 ++
>  drivers/net/i40e/i40e_ethdev.c              |   4 +
>  drivers/net/i40e/i40e_rxtx.c                | 183 ++++++++++++++++++++++++----
>  lib/librte_ether/rte_ethdev.c               |  30 +++--
>  lib/librte_ether/rte_ethdev.h               |   7 ++
>  7 files changed, 333 insertions(+), 35 deletions(-)
> 
> --

Acked-by: Konstantin Ananyev <konstantin.ananyev at intel.com>

> 2.13.6