[dpdk-dev] [PATCH v4 03/11] net/mlx5: support L3 VXLAN flow

[Xueming(Steven) Li]

> -----Original Message-----
> From: Nélio Laranjeiro <nelio.laranjeiro at 6wind.com>
> Sent: Thursday, April 19, 2018 2:56 PM
> To: Xueming(Steven) Li <xuemingl at mellanox.com>
> Cc: Shahaf Shuler <shahafs at mellanox.com>; dev at dpdk.org
> Subject: Re: [PATCH v4 03/11] net/mlx5: support L3 VXLAN flow
> 
> On Thu, Apr 19, 2018 at 06:20:50AM +0000, Xueming(Steven) Li wrote:
> >
> >
> > > -----Original Message-----
> > > From: Nélio Laranjeiro <nelio.laranjeiro at 6wind.com>
> > > Sent: Wednesday, April 18, 2018 11:09 PM
> > > To: Xueming(Steven) Li <xuemingl at mellanox.com>
> > > Cc: Shahaf Shuler <shahafs at mellanox.com>; dev at dpdk.org
> > > Subject: Re: [PATCH v4 03/11] net/mlx5: support L3 VXLAN flow
> > >
> > > On Wed, Apr 18, 2018 at 02:43:30PM +0000, Xueming(Steven) Li wrote:
> > > >
> > > >
> > > > > -----Original Message-----
> > > > > From: Nélio Laranjeiro <nelio.laranjeiro at 6wind.com>
> > > > > Sent: Wednesday, April 18, 2018 2:49 PM
> > > > > To: Xueming(Steven) Li <xuemingl at mellanox.com>
> > > > > Cc: Shahaf Shuler <shahafs at mellanox.com>; dev at dpdk.org
> > > > > Subject: Re: [PATCH v4 03/11] net/mlx5: support L3 VXLAN flow
> > > > >
> > > > > On Tue, Apr 17, 2018 at 11:14:28PM +0800, Xueming Li wrote:
> > > > > > This patch support L3 VXLAN, no inner L2 header comparing to
> > > > > > standard VXLAN protocol. L3 VXLAN using specific overlay UDP
> > > > > > destination port to discriminate against standard VXLAN, FW
> > > > > > has to be configured to support
> > > > > > it:
> > > > > >   sudo mlxconfig -d <device> -y s IP_OVER_VXLAN_EN=1
> > > > > >   sudo mlxconfig -d <device> -y s IP_OVER_VXLAN_PORT=<port>
> > > > > >
> > > > > > Signed-off-by: Xueming Li <xuemingl at mellanox.com>
> > > > > > ---
> > > > > >  drivers/net/mlx5/mlx5_flow.c | 4 +++-
> > > > > >  1 file changed, 3 insertions(+), 1 deletion(-)
> > > > > >
> > > > > > diff --git a/drivers/net/mlx5/mlx5_flow.c
> > > > > > b/drivers/net/mlx5/mlx5_flow.c index 771d5f14d..d7a921dff
> > > > > > 100644
> > > > > > --- a/drivers/net/mlx5/mlx5_flow.c
> > > > > > +++ b/drivers/net/mlx5/mlx5_flow.c
> > > > > > @@ -413,7 +413,9 @@ static const struct mlx5_flow_items mlx5_flow_items[] = {
> > > > > >  		.dst_sz = sizeof(struct ibv_flow_spec_tunnel),
> > > > > >  	},
> > > > > >  	[RTE_FLOW_ITEM_TYPE_VXLAN] = {
> > > > > > -		.items = ITEMS(RTE_FLOW_ITEM_TYPE_ETH),
> > > > > > +		.items = ITEMS(RTE_FLOW_ITEM_TYPE_ETH,
> > > > > > +			       RTE_FLOW_ITEM_TYPE_IPV4, /* For L3 VXLAN. */
> > > > > > +			       RTE_FLOW_ITEM_TYPE_IPV6), /* For L3 VXLAN. */
> > > > > >  		.actions = valid_actions,
> > > > > >  		.mask = &(const struct rte_flow_item_vxlan){
> > > > > >  			.vni = "\xff\xff\xff",
> > > > > > --
> > > > > > 2.13.3
> > > > >
> > > > > Such support must be under device parameter has it depends on
> > > > > the configuration of the firmware.  If the firmware is not
> > > > > correctly configured the PMD must refuse
> > > such rule.
> > > > >
> > > > > Thanks,
> > > > >
> > > > > --
> > > > > Nélio Laranjeiro
> > > > > 6WIND
> > > >
> > > > Are you suggesting Verbs parameter? I'm afraid we can't have it in
> > > > short time, need new patch in later release when Verbs ready.
> > >
> > > Take a look at [1], this is what I mean.
> >
> > Enabling a new device parameter can't make L3 VXLAN packet get
> > received if fw configuration not set.
> 
> So you expect than the user will enable a feature without reading the PMD documentation?
> If it is the case, the answer it pretty simple, it is the same as above, read the PMD documentation.
> 
> > On the other hand, if fw continuation enabled and device parameter not
> > set, packet could be received but failed to create rule.
> 
> Again a user using a NIC should read the documentation.

If a user read the document, fw should be configured correctly to enable this feature.

> 
> > I'm afraid that a device parameter will introduce complexity of using
> > this feature w/o real benefits.
> 
> Add this missing device parameter and update accordingly the documentation, or wait for Verbs to add
> the missing query feature.
> 
> If the firmware it not configured this rule must be refused, as there is no way in the PMD to know if
> the firmware is configured, it must rely on a device parameter.

Let's keep the design simple, users know exactly what they are doing and should not expecting 
such flow working by reading document.

> 
> Regards,
> 
> --
> Nélio Laranjeiro
> 6WIND