[dpdk-dev] [PATCH] net/ixgbe: add support of loopback for X540/X550

[Zhao1, Wei]

Hi，Meunier, Julien

> -----Original Message-----
> From: Meunier, Julien (Nokia - FR/Paris-Saclay)
> [mailto:julien.meunier at nokia.com]
> Sent: Tuesday, January 8, 2019 12:05 AM
> To: Zhao1, Wei <wei.zhao1 at intel.com>; Ananyev, Konstantin
> <konstantin.ananyev at intel.com>; Lu, Wenzhuo <wenzhuo.lu at intel.com>
> Cc: dev at dpdk.org
> Subject: Re: [dpdk-dev] [PATCH] net/ixgbe: add support of loopback for
> X540/X550
> 
> Inline reply
> 
> On 07/01/2019 11:05, Zhao1, Wei wrote:
> >
> >
> >> -----Original Message-----
> >> From: dev [mailto:dev-bounces at dpdk.org] On Behalf Of Julien Meunier
> >> Sent: Thursday, January 3, 2019 12:01 AM
> >> To: Ananyev, Konstantin <konstantin.ananyev at intel.com>; Lu, Wenzhuo
> >> <wenzhuo.lu at intel.com>
> >> Cc: dev at dpdk.org
> >> Subject: [dpdk-dev] [PATCH] net/ixgbe: add support of loopback for
> >> X540/X550
> >>
> >> Loopback mode is also supported on X540 and X550 NICs, according to
> >> their datasheet (section 15.2). The way to set it up is a little different of
> the 82599.
> >>
> >> Signed-off-by: Julien Meunier <julien.meunier at nokia.com>
> [...]
> 
> >> diff --git a/drivers/net/ixgbe/ixgbe_rxtx.c
> >> b/drivers/net/ixgbe/ixgbe_rxtx.c index 9a79d18..0ef7fdf 100644
> >> --- a/drivers/net/ixgbe/ixgbe_rxtx.c
> >> +++ b/drivers/net/ixgbe/ixgbe_rxtx.c
> 
> [...]
> 
> >>   /*
> >>    * Start Transmit and Receive Units.
> >> @@ -5148,10 +5175,16 @@ ixgbe_dev_rxtx_start(struct rte_eth_dev
> *dev)
> >>   	rxctrl |= IXGBE_RXCTRL_RXEN;
> >>   	hw->mac.ops.enable_rx_dma(hw, rxctrl);
> >>
> >> -	/* If loopback mode is enabled for 82599, set up the link accordingly
> >> */
> >> -	if (hw->mac.type == ixgbe_mac_82599EB &&
> >> -			dev->data->dev_conf.lpbk_mode ==
> >> IXGBE_LPBK_82599_TX_RX)
> >> -		ixgbe_setup_loopback_link_82599(hw);
> >> +	/* If loopback mode is enabled, set up the link accordingly */
> >> +	if (dev->data->dev_conf.lpbk_mode == IXGBE_LPBK_TX_RX) {
> >> +		if (hw->mac.type == ixgbe_mac_82599EB)
> >> +			ixgbe_setup_loopback_link_82599(hw);
> >> +		else if (hw->mac.type == ixgbe_mac_X540 ||
> >> +		     hw->mac.type == ixgbe_mac_X550 ||
> >> +		     hw->mac.type == ixgbe_mac_X550EM_x ||
> >> +		     hw->mac.type == ixgbe_mac_X550EM_a)
> >> +			ixgbe_setup_loopback_link_x540_x550(hw);
> > 		Else
> > 			Return -1;
> >
> > SHOULD we add some branch here?
> > In case some other NIC with configuration for tx->rx loop but pmd code do
> not support.
> 
> My patch is iso-functional: if a user sets the lpbk_mode to 0x1
> (IXGBE_LPBK_TX_RX), DPDK setups the TX -> RX loopback. Otherwise, it
> ignores the configuration.
> 
> Please remember that lpbk_mode is specific to each PMD.
> 
> in rte_ethdev.h:
> 	Loopback operation mode. By default the value is 0, meaning the
> 	loopback mode is disabled. Read the datasheet of given ethernet
> 	controller for details. The possible values of this field are
> 	defined in implementation of each driver.
> 
> Other PMD can implement TX -> RX with other value.
> 
> Do I need to add more check around this LPBK ?

Yes, 
"	Else
		Return -1;
"  
is need 
My concern is  such a case:
If some user is using 82598, and he set lpbk_mode to IXGBE_LPBK_TX_RX, 
In fact Our IXGBE PMD do not support loopback mode for 82598, but we do not return error for that invalid configuration!!
So, we need some check for NIC type and error reminder.


   
> 
> >
> >> +	}
> >
> >>
> >>   #ifdef RTE_LIBRTE_SECURITY
> >>   	if ((dev->data->dev_conf.rxmode.offloads &
> >> --
> >> 2.10.2
> >
> 
> Thanks,
> Best regards,
> Julien Meunier