[dpdk-dev] [Suspected-Phishing][PATCH v3] net/mlx5: support IP-in-IP tunnel

[Jack Min]

On Wed, 19-07-10, 22:35, Slava Ovsiienko wrote:
> Regarding point 2) - it is OK, there is common flags update in the item validation loop.
> So, after update point 1) - you can add my Acked-by to the patch, thanks.
Great! thank you~
I'll update it soon.

> 
> WBR,
> Slava
> 
> > -----Original Message-----
> > From: dev <dev-bounces at dpdk.org> On Behalf Of Slava Ovsiienko
> > Sent: Wednesday, July 10, 2019 17:20
> > To: Jack Min <jackmin at mellanox.com>; Raslan Darawsheh
> > <rasland at mellanox.com>; Shahaf Shuler <shahafs at mellanox.com>;
> > Yongseok Koh <yskoh at mellanox.com>; John McNamara
> > <john.mcnamara at intel.com>; Marko Kovacevic
> > <marko.kovacevic at intel.com>
> > Cc: dev at dpdk.org
> > Subject: Re: [dpdk-dev] [Suspected-Phishing][PATCH v3] net/mlx5: support
> > IP-in-IP tunnel
> > 
> > Hi, Xiaoyu
> > 
> > There is a couple of small points to note:
> > 1) It would be good to have the testpmd flow create command sample with
> > new tunnels in commit log.
> > 2) is it OK: "mlx5_flow_tunnel_ip_check(items, &last_item); " ?
> >     It looks like a bug, should the second parameter be "&item_flags" ? (if so -
> > please, fix all
> >    calls of mlx5_flow_tunnel_ip_check())
> > 
> > WBR,
> > Slava
> > 
> > > -----Original Message-----
> > > From: Xiaoyu Min <jackmin at mellanox.com>
> > > Sent: Wednesday, July 10, 2019 13:15
> > > To: Raslan Darawsheh <rasland at mellanox.com>; Slava Ovsiienko
> > > <viacheslavo at mellanox.com>; Shahaf Shuler <shahafs at mellanox.com>;
> > > Yongseok Koh <yskoh at mellanox.com>; John McNamara
> > > <john.mcnamara at intel.com>; Marko Kovacevic
> > <marko.kovacevic at intel.com>
> > > Cc: dev at dpdk.org
> > > Subject: [Suspected-Phishing][PATCH v3] net/mlx5: support IP-in-IP
> > > tunnel
> > >
> > > Enabled IP-in-IP tunnel type support on DV/DR flow engine.
> > > This includes the following combination:
> > >  - IPv4 over IPv4
> > >  - IPv4 over IPv6
> > >  - IPv6 over IPv4
> > >  - IPv6 over IPv6
> > >
> > > MLX5 NIC supports IP-in-IP tunnel via FLEX Parser so need to make sure
> > > fw using FLEX Paser profile 0.
> > >
> > >   mlxconfig -d <mst device> -y set FLEX_PARSER_PROFILE_ENABLE=0
> > >
> > > Signed-off-by: Xiaoyu Min <jackmin at mellanox.com>
> > > ---
> > > v2:
> > >   * updated release note
> > > v3:
> > >   * rebased on 19.08-rc1
> > > ---
> > >  doc/guides/nics/mlx5.rst               | 15 ++++++++++-
> > >  doc/guides/rel_notes/release_19_08.rst |  1 +
> > >  drivers/net/mlx5/mlx5_flow.c           | 35 ++++++++++++++++++++++++
> > >  drivers/net/mlx5/mlx5_flow.h           |  6 ++++-
> > >  drivers/net/mlx5/mlx5_flow_dv.c        | 37 ++++++++++++++++++++++++++
> > >  5 files changed, 92 insertions(+), 2 deletions(-)
> > >