[dpdk-dev] [PATCH] doc: fix typing error in example/l3_forward_access_ctrl
David Marchand
david.marchand at redhat.com
Thu Nov 5 09:54:33 CET 2020
On Mon, Nov 2, 2020 at 12:20 PM Ibtisam Tariq <ibtisam.tariq at emumba.com> wrote:
>
> Add "--" and remove extra spaces in l3fwd-acl commands.
>
> Fixes: d0dff9ba4 ("doc: sample application user guide")
> Cc: bernard.iremonger at intel.com
>
> Signed-off-by: Ibtisam Tariq <ibtisam.tariq at emumba.com>
> ---
> doc/guides/sample_app_ug/l3_forward_access_ctrl.rst | 8 ++++----
> 1 file changed, 4 insertions(+), 4 deletions(-)
>
> diff --git a/doc/guides/sample_app_ug/l3_forward_access_ctrl.rst b/doc/guides/sample_app_ug/l3_forward_access_ctrl.rst
> index 4a96800ec..3cdfbfb17 100644
> --- a/doc/guides/sample_app_ug/l3_forward_access_ctrl.rst
> +++ b/doc/guides/sample_app_ug/l3_forward_access_ctrl.rst
> @@ -236,7 +236,7 @@ The application has a number of command line options:
>
> .. code-block:: console
>
> - ./<build_dir>/examples/dpdk-l3fwd-acl [EAL options] -- -p PORTMASK [-P] --config(port,queue,lcore)[,(port,queue,lcore)] --rule_ipv4 FILENAME rule_ipv6 FILENAME [--alg=<val>] [--enable-jumbo [--max-pkt-len PKTLEN]] [--no-numa] [--eth-dest=X,MM:MM:MM:MM:MM:MM]
> + ./<build_dir>/examples/dpdk-l3fwd-acl [EAL options] -- -p PORTMASK [-P] --config(port,queue,lcore)[,(port,queue,lcore)] --rule_ipv4 FILENAME --rule_ipv6 FILENAME [--alg=<val>] [--enable-jumbo [--max-pkt-len PKTLEN]] [--no-numa] [--eth-dest=X,MM:MM:MM:MM:MM:MM]
>
>
> where,
> @@ -271,7 +271,7 @@ To enable L3 forwarding between two ports, assuming that both ports are in the s
>
> .. code-block:: console
>
> - ./<build_dir>/examples/dpdk-l3fwd-acl -l 1,2 -n 4 -- -p 0x3 --config="(0,0,1),(1,0,2)" --rule_ipv4="./rule_ipv4.db" -- rule_ipv6="./rule_ipv6.db" --alg=scalar
> + ./<build_dir>/examples/dpdk-l3fwd-acl -l 1,2 -n 4 -- -p 0x3 --config="(0,0,1),(1,0,2)" --rule_ipv4="./rule_ipv4.db" --rule_ipv6="./rule_ipv6.db" --alg=scalar
>
> In this command:
>
> @@ -293,9 +293,9 @@ In this command:
> | | | | |
> +----------+------------+-----------+-------------------------------------+
>
> -* The --rule_ipv4 option specifies the reading of IPv4 rules sets from the ./ rule_ipv4.db file.
> +* The --rule_ipv4 option specifies the reading of IPv4 rules sets from the ./rule_ipv4.db file.
No point in keeping the ./ and I would remove it in the cmdline
example above too.
> -* The --rule_ipv6 option specifies the reading of IPv6 rules sets from the ./ rule_ipv6.db file.
> +* The --rule_ipv6 option specifies the reading of IPv6 rules sets from the ./rule_ipv6.db file.
>
> * The --alg=scalar option specifies the performing of rule lookup with a scalar function.
>
> --
> 2.17.1
>
Reviewed-by: David Marchand <david.marchand at redhat.com>
Thanks.
--
David Marchand
More information about the dev
mailing list