[dts] [PATCH] L3fwd: Enable RFC2544 for some 2 ports cases

[Liu, Yong]

Hi Heng,

One question about RFC2544 test.

According to https://tools.ietf.org/html/rfc2544, one minute is enough for trial. Wait for two minutes maybe too long for validation.
And frame should be [64, 128, 256, 512, 1024, 1280, 1518], maybe you can reference it.

> -----Original Message-----
> From: dts [mailto:dts-bounces at dpdk.org] On Behalf Of Ding Heng
> Sent: Monday, December 14, 2015 5:36 PM
> To: dts at dpdk.org
> Cc: Ding, HengX
> Subject: [dts] [PATCH] L3fwd: Enable RFC2544 for some 2 ports cases
> 
> Enable RFC2544 test for l3fwd 2 ports cases. In order to save time, only
> 1S/1C/1T and 1S/4C/1T cases will be enabled, the others' result will be
> set 0.
> 
> Signed-off-by: Ding Heng <hengx.ding at intel.com>
> 
> diff --git a/tests/TestSuite_l3fwd.py b/tests/TestSuite_l3fwd.py
> index 0e09256..ea4e3ca 100644
> --- a/tests/TestSuite_l3fwd.py
> +++ b/tests/TestSuite_l3fwd.py
> @@ -521,7 +521,7 @@ class TestL3fwd(TestCase,IxiaPacketGenerator):
>          L3fwd main 2 ports.
>          """
> 
> -        header_row = ["Frame", "Ports", "S/C/T", "Mpps", "% linerate",
> "mode"]
> +        header_row = ["Frame", "mode", "S/C/T", "Mpps", "% linerate",
> "LR_tx_pkts(2mins)", "LR_rx_pkts(2mins)", "LR_loss_pkts(2mins)", "%
> zero_loss_rate"]
>          self.l3fwd_test_results['header'] = header_row
>          dts.results_table_add_header(header_row)
>          self.l3fwd_test_results['data'] = []
> @@ -533,7 +533,7 @@ class TestL3fwd(TestCase,IxiaPacketGenerator):
>                  HEADER_SIZE['ip'] - HEADER_SIZE['eth']
>              for _port in range(2):
>                  dmac = self.dut.get_mac_address(valports[_port])
> -                flows = ['Ether(dst=%s)/%s/("X"*%d)' % (dmac, flow,
> payload_size) for flow in self.flows()[_port *2:(_port +1)*2]]
> +                flows = ['Ether(dst="%s")/%s/("X"*%d)' % (dmac, flow,
> payload_size) for flow in self.flows()[_port *2:(_port +1)*2]]
>                  self.tester.scapy_append('wrpcap("dst%d.pcap",
> [%s])' %(valports[_port],string.join(flows,',')))
>              self.tester.scapy_execute()
> 
> @@ -605,13 +605,18 @@ class TestL3fwd(TestCase,IxiaPacketGenerator):
>                      pps /= 1000000.0
>                      linerate = self.wirespeed(self.nic, frame_size, 2)
>                      pct = pps * 100 / linerate
Not sure why not "lpm" mode and 1C/4C need RFC2544 test.  Could you clear it?

> +                    if mode == "lpm" and (cores == "1S/1C/1T" or cores ==
> "1S/4C/1T"):
> +                        zero_loss_rate, tx_pkts, rx_pkts =
> self.tester.run_rfc2544(tgenInput, delay=3)
> +                        loss_pkts = tx_pkts - rx_pkts
> +                    else:
> +                        zero_loss_rate=tx_pkts=rx_pkts=loss_pkts=0
> 
>                      index += 1
> 
>                      # Stop l3fwd
>                      self.dut.send_expect("^C", "#")
> 
> -                    data_row = [frame_size, 2, cores, str(pps), str(pct),
> mode]
> +                    data_row = [frame_size, mode, cores, str(pps),
> str(pct), tx_pkts, rx_pkts, loss_pkts, zero_loss_rate]
>                      dts.results_table_add_row(data_row)
>                      self.l3fwd_test_results['data'].append(data_row)
> 
> --
> 1.9.3