[dts] [PATCH] test_plan: add hotplug_test_plan

[Iremonger, Bernard]

> -----Original Message-----
> From: Qiu, Michael
> Sent: Tuesday, February 10, 2015 8:55 AM
> To: Tetsuya Mukawa; dts at dpdk.org
> Cc: Iremonger, Bernard
> Subject: Re: [PATCH] test_plan: add hotplug_test_plan
> 
> On 2/10/2015 11:24 AM, Tetsuya Mukawa wrote:
> > Hi Michael,
> >
> > On 2015/02/09 22:13, Qiu, Michael wrote:
> >> [+cc] Bernard
> >>
> >> Hi, Bernard and Tetsuya
> >>
> >> Would you have time to review this test plan?
> >> Your comments are very important.
> >>
> >> Thanks,
> >> Michael
> >> On 2/2/2015 4:47 PM, Qiu, Michael wrote:
> 
> [...]
> 
> >> +
> >> +Prerequisites
> >> +-------------
> >> +Assume DPDK managerd at least one device for physical or none for virtual.
> > "managerd" may be typo.
> >
> >>> +This feature only supports igb_uio now, for uio_pci_generic is on
> >>> +the way, will test it after enabled.
> >>> +
> >>> +To run the testpmd application in linuxapp environment with 4
> >>> +lcores,
> >>> +4 channels with other default parameters in interactive mode.
> >>> +
> >>> +        $ ./testpmd -c 0xf -n 4 -- -i
> >>> +
> >>> +Test ENV:
> >>> +
> >>> +All test case can be run in 32bit and 64bit platform.
> >>> +
> >>> +All os can be support, like fedora, ubuntu, rhel, suse, but freebsd
> >>> +will not include as hotplug has no plan to support that platform
> >>> +
> >>> +All kernel version(start from 2.6) can be support, for vfio need kernel
> >>> +        version greater than 3.6.
> >>> +
> >>> +Virtulization support: KVM/VMware/Xen, container is in the roadmap
> > "Virtulization" may be typo.
> >
> >>> +
> >>> +-------------------------------------------------------------------
> >>> +------------ Test Case 1: port dettach & attach for physical
> >>> +devices with igb_uio
> >>> +-------------------------------------------------------------------
> >>> +------------
> >>> +1. run "port attach 0000:02:00.0",
> >>> +   assume the physical devices is BDF is 0000:02:00.0
> > Above sentence may be typo.
> 
> [...]
> 
> > Usually before submitting hotplug patches, I test almost same as
> > above, and additionally below cases.
> >
> > ---------------------------
> > Test Re-attach
> > ---------------------------
> >   - testpmd> attach
> >  - testpmd> port start
> >  - testpmd> start
> >  - testpmd> stop
> >  - testpmd> port stop
> >  - testpmd> port close
> >  - testpmd> port detach
> >  - testpmd> port attach
> >  - testpmd> port start
> >  - testpmd> start
> >  - testpmd> stop
> >   (To check if re-attached port works fine.)
> 
> This will be added for every test case
> 
> > ---------------------------
> > start testpmd with "--vdev" option, and detach.
> > ---------------------------
> >
> >   - ./testpmd -c 0xf -n 4 --vdev "eth_pcap0,iface=<interface>" -- -i
> >  - testpmd> start
> >  - testpmd> stop
> >  - testpmd> port stop
> >  - testpmd> port close
> >  - testpmd> port detach
> >    (To make sure if we can detach the port)
> >
> > ---------------------------
> > start testpmd with an attached physical NIC port, and detach.
> > ---------------------------
> >   - ./dpdk_nic_bind -b igb_uio <pci address>
> >  - ./testpmd -c 0xf -n 4 -- -i
> >  - testpmd> start
> >  - testpmd> stop
> >  - testpmd> port stop
> >  - testpmd> port close
> >  - testpmd> port detach
> >    (To make sure if we can detach the port)
> 
> I will add both.
> 
> Thanks,
> Michael
> > How about adding such cases?
> >
> > Thanks,
> > Tetsuya
> >
> >
Hi Michael, Tetsuya,

Should there be test cases added using pmd_null (eth_null0) ?

Regards,

Bernard.