[dts] Minimum Tester/DUT configuration
john miller
john.miller at atomicrules.com
Tue Jan 24 17:10:44 CET 2017
Thank you for your response.
We have updated our tester and DUT configuration. We have 2 Fortville eagles in our tester and 1 Fortville spirit configured as a 4x10 in our DUT. We have link on all 4 ports.
We are trying to run the l2fwd DTS test and we get this error.
"EAL: Error - exiting with code: 1
Cause: No Ethernet ports - bye”
The complete output is shown below. I searched the forums for this error and got a few hits but none of the matching threads seemed like what we are experiencing. Could you help us isolate this issue ?
Thank you,
-John
DUT 192.168.0.34
INFO: ssh root at 192.168.0.36
INFO: ssh root at 192.168.0.36
INFO: ssh root at 192.168.0.34
INFO: ssh root at 192.168.0.34
INFO: CACHE: Cache will not be read.
INFO: SKIP: The DPDK setup steps will be executed.
DTS_TESTER_CMD: scp -v dep/tgen.tgz root at 192.168.0.36:~/
DTS_TESTER_CMD: scp -v dep/tclclient.tgz root at 192.168.0.36:~/
DTS_TESTER_CMD: tar zxf tgen.tgz
DTS_TESTER_CMD: tar zxf tclclient.tgz
DTS_TESTER_CMD: modprobe uio
DTS_TESTER_CMD: modprobe igb
DTS_TESTER_CMD: modprobe ixgbe
DTS_TESTER_CMD: modprobe e1000e
DTS_TESTER_CMD: modprobe e1000
DTS_TESTER_CMD: cat /sys/bus/pci/devices/0000\:00\:19.0/vendor
DTS_TESTER_CMD: cat /sys/bus/pci/devices/0000\:00\:19.0/device
DTS_TESTER_CMD: cat /sys/bus/pci/devices/0000\:00\:19.0/vendor
DTS_TESTER_CMD: cat /sys/bus/pci/devices/0000\:00\:19.0/device
DTS_TESTER_CMD: ifconfig eno1 up
DTS_TESTER_CMD: cat /sys/bus/pci/devices/0000\:01\:00.0/vendor
DTS_TESTER_CMD: cat /sys/bus/pci/devices/0000\:01\:00.0/device
DTS_TESTER_CMD: cat /sys/bus/pci/devices/0000\:01\:00.0/vendor
DTS_TESTER_CMD: cat /sys/bus/pci/devices/0000\:01\:00.0/device
DTS_TESTER_CMD: ifconfig enp1s0f0 up
DTS_TESTER_CMD: cat /sys/bus/pci/devices/0000\:01\:00.1/vendor
DTS_TESTER_CMD: cat /sys/bus/pci/devices/0000\:01\:00.1/device
DTS_TESTER_CMD: cat /sys/bus/pci/devices/0000\:01\:00.1/vendor
DTS_TESTER_CMD: cat /sys/bus/pci/devices/0000\:01\:00.1/device
DTS_TESTER_CMD: ifconfig enp1s0f1 up
DTS_TESTER_CMD: cat /sys/bus/pci/devices/0000\:02\:00.0/vendor
DTS_TESTER_CMD: cat /sys/bus/pci/devices/0000\:02\:00.0/device
DTS_TESTER_CMD: cat /sys/bus/pci/devices/0000\:02\:00.0/vendor
DTS_TESTER_CMD: cat /sys/bus/pci/devices/0000\:02\:00.0/device
DTS_TESTER_CMD: ifconfig enp2s0f0 up
DTS_TESTER_CMD: cat /sys/bus/pci/devices/0000\:02\:00.1/vendor
DTS_TESTER_CMD: cat /sys/bus/pci/devices/0000\:02\:00.1/device
DTS_TESTER_CMD: cat /sys/bus/pci/devices/0000\:02\:00.1/vendor
DTS_TESTER_CMD: cat /sys/bus/pci/devices/0000\:02\:00.1/device
DTS_TESTER_CMD: ifconfig enp2s0f1 up
DTS_TESTER_CMD: Tester: [0000:00:19.0 8086:1503] unknow_nic
DTS_TESTER_CMD: Tester: [0000:01:00.0 8086:1572] enp1s0f0
DTS_TESTER_CMD: Tester: [0000:01:00.1 8086:1572] enp1s0f1
DTS_TESTER_CMD: Tester: [0000:02:00.0 8086:1572] enp2s0f0
DTS_TESTER_CMD: Tester: [0000:02:00.1 8086:1572] enp2s0f1
DTS_TESTER_CMD: {'intf': 'enp1s0f0', 'mac': '3c:fd:fe:9c:c3:4c', 'pci': '0000:01:00.0', 'ipv6': 'fe80::23af:6b1b:3fca:fe8a', 'type': '8086:1572', 'port': <net_device.NetDevice object at 0x7f5c8f549cd0>}
DTS_TESTER_CMD: {'intf': 'enp1s0f1', 'mac': '3c:fd:fe:9c:c3:4d', 'pci': '0000:01:00.1', 'ipv6': 'fe80::2e0:6ec:56c9:1b3', 'type': '8086:1572', 'port': <net_device.NetDevice object at 0x7f5c8f571110>}
DTS_TESTER_CMD: {'intf': 'enp2s0f0', 'mac': '3c:fd:fe:9e:11:c0', 'pci': '0000:02:00.0', 'ipv6': 'fe80::27d1:7383:502b:2486', 'type': '8086:1572', 'port': <net_device.NetDevice object at 0x7f5c8f549e90>}
DTS_TESTER_CMD: {'intf': 'enp2s0f1', 'mac': '3c:fd:fe:9e:11:c1', 'pci': '0000:02:00.1', 'ipv6': 'fe80::b4d0:ec1f:fe29:687f', 'type': '8086:1572', 'port': <net_device.NetDevice object at 0x7f5c8f549c90>}
DTS_DUT_CMD: [192.168.0.34] ls /tmp/ && cd ~
DTS_DUT_CMD: [192.168.0.34] scp -v dep/dpdk.tar.gz root at 192.168.0.34:/tmp/
DTS_DUT_CMD: [192.168.0.34] ulimit -c unlimited
DTS_DUT_CMD: [192.168.0.34] rm -rf ~/dpdk
DTS_DUT_CMD: [192.168.0.34] tar zxf /tmp/dpdk.tar.gz -C ~
DTS_DUT_CMD: [192.168.0.34] ls ~/dpdk
DTS_DUT_CMD: [192.168.0.34] cd ~/dpdk
DTS_DUT_CMD: [192.168.0.34] alias ls='ls --color=none'
DTS_DUT_CMD: [192.168.0.34] DUT: [0000:00:1f.6 8086:15b8] Skipped: Unknown/not selected
DTS_DUT_CMD: [192.168.0.34] cat /sys/bus/pci/devices/0000\:02\:00.0/vendor
DTS_DUT_CMD: [192.168.0.34] cat /sys/bus/pci/devices/0000\:02\:00.0/device
DTS_DUT_CMD: [192.168.0.34] cat /sys/bus/pci/devices/0000\:02\:00.0/vendor
DTS_DUT_CMD: [192.168.0.34] cat /sys/bus/pci/devices/0000\:02\:00.0/device
DTS_DUT_CMD: [192.168.0.34] cat /sys/bus/pci/devices/0000\:02\:00.1/vendor
DTS_DUT_CMD: [192.168.0.34] cat /sys/bus/pci/devices/0000\:02\:00.1/device
DTS_DUT_CMD: [192.168.0.34] cat /sys/bus/pci/devices/0000\:02\:00.1/vendor
DTS_DUT_CMD: [192.168.0.34] cat /sys/bus/pci/devices/0000\:02\:00.1/device
DTS_DUT_CMD: [192.168.0.34] cat /sys/bus/pci/devices/0000\:02\:00.2/vendor
DTS_DUT_CMD: [192.168.0.34] cat /sys/bus/pci/devices/0000\:02\:00.2/device
DTS_DUT_CMD: [192.168.0.34] cat /sys/bus/pci/devices/0000\:02\:00.2/vendor
DTS_DUT_CMD: [192.168.0.34] cat /sys/bus/pci/devices/0000\:02\:00.2/device
DTS_DUT_CMD: [192.168.0.34] cat /sys/bus/pci/devices/0000\:02\:00.3/vendor
DTS_DUT_CMD: [192.168.0.34] cat /sys/bus/pci/devices/0000\:02\:00.3/device
DTS_DUT_CMD: [192.168.0.34] cat /sys/bus/pci/devices/0000\:02\:00.3/vendor
DTS_DUT_CMD: [192.168.0.34] cat /sys/bus/pci/devices/0000\:02\:00.3/device
DTS_DUT_CMD: [192.168.0.34] echo 0000:02:00.0 > /sys/bus/pci/devices/0000\:02\:00.0/driver/unbind
DTS_DUT_CMD: [192.168.0.34] modprobe i40e
DTS_DUT_CMD: [192.168.0.34] echo 0000:02:00.0 > /sys/bus/pci/drivers/i40e/bind
DTS_DUT_CMD: [192.168.0.34] ifconfig eth6 up
DTS_DUT_CMD: [192.168.0.34] echo 0000:02:00.1 > /sys/bus/pci/devices/0000\:02\:00.1/driver/unbind
DTS_DUT_CMD: [192.168.0.34] modprobe i40e
DTS_DUT_CMD: [192.168.0.34] echo 0000:02:00.1 > /sys/bus/pci/drivers/i40e/bind
DTS_DUT_CMD: [192.168.0.34] ifconfig eth5 up
DTS_DUT_CMD: [192.168.0.34] echo 0000:02:00.2 > /sys/bus/pci/devices/0000\:02\:00.2/driver/unbind
DTS_DUT_CMD: [192.168.0.34] modprobe i40e
DTS_DUT_CMD: [192.168.0.34] echo 0000:02:00.2 > /sys/bus/pci/drivers/i40e/bind
DTS_DUT_CMD: [192.168.0.34] ifconfig eth7 up
DTS_DUT_CMD: [192.168.0.34] echo 0000:02:00.3 > /sys/bus/pci/devices/0000\:02\:00.3/driver/unbind
DTS_DUT_CMD: [192.168.0.34] modprobe i40e
DTS_DUT_CMD: [192.168.0.34] echo 0000:02:00.3 > /sys/bus/pci/drivers/i40e/bind
DTS_DUT_CMD: [192.168.0.34] ifconfig eth8 up
DTS_DUT_CMD: [192.168.0.34] ip link show eth6
DTS_DUT_CMD: [192.168.0.34] ip -family inet6 address show dev eth6 | awk '/inet6/ { print $2 }'
DTS_DUT_CMD: [192.168.0.34] ip link show eth5
DTS_DUT_CMD: [192.168.0.34] ip -family inet6 address show dev eth5 | awk '/inet6/ { print $2 }'
DTS_DUT_CMD: [192.168.0.34] ip link show eth7
DTS_DUT_CMD: [192.168.0.34] ip -family inet6 address show dev eth7 | awk '/inet6/ { print $2 }'
DTS_DUT_CMD: [192.168.0.34] ip link show eth8
DTS_DUT_CMD: [192.168.0.34] ip -family inet6 address show dev eth8 | awk '/inet6/ { print $2 }'
DTS_TESTER_CMD: ping6 -w 5 -c 5 -A fe80::3efd:feff:fea0:fbc0%enp1s0f0
DTS_TESTER_CMD: ping6 -w 5 -c 5 -A fe80::3efd:feff:fea0:fbc0%enp1s0f1
DTS_TESTER_CMD: ping6 -w 5 -c 5 -A fe80::3efd:feff:fea0:fbc0%enp2s0f0
DTS_TESTER_CMD: ping6 -w 5 -c 5 -A fe80::3efd:feff:fea0:fbc0%enp2s0f1
DTS_DUT_CMD: [192.168.0.34] PORT MAP: [dut 0: tester 3]
DTS_TESTER_CMD: ping6 -w 5 -c 5 -A fe80::3efd:feff:fea0:fbc1%enp1s0f0
DTS_TESTER_CMD: ping6 -w 5 -c 5 -A fe80::3efd:feff:fea0:fbc1%enp1s0f1
DTS_TESTER_CMD: ping6 -w 5 -c 5 -A fe80::3efd:feff:fea0:fbc1%enp2s0f0
DTS_DUT_CMD: [192.168.0.34] PORT MAP: [dut 1: tester 2]
DTS_TESTER_CMD: ping6 -w 5 -c 5 -A fe80::3efd:feff:fea0:fbc2%enp1s0f0
DTS_TESTER_CMD: ping6 -w 5 -c 5 -A fe80::3efd:feff:fea0:fbc2%enp1s0f1
DTS_DUT_CMD: [192.168.0.34] PORT MAP: [dut 2: tester 1]
DTS_TESTER_CMD: ping6 -w 5 -c 5 -A fe80::3efd:feff:fea0:fbc3%enp1s0f0
DTS_DUT_CMD: [192.168.0.34] PORT MAP: [dut 3: tester 0]
DTS_DUT_RESULT: [192.168.0.34] DUT PORT MAP: [3, 2, 1, 0]
DTS_DUT_CMD: [192.168.0.34] {'intf': 'eth6', 'mac': '3c:fd:fe:a0:fb:c0', 'pci': '0000:02:00.0', 'numa': -1, 'ipv6': 'fe80::3efd:feff:fea0:fbc0', 'type': '8086:1583', 'port': <net_device.NetDevice object at 0x7f5c8f571650>}
DTS_DUT_CMD: [192.168.0.34] {'intf': 'eth5', 'mac': '3c:fd:fe:a0:fb:c1', 'pci': '0000:02:00.1', 'numa': -1, 'ipv6': 'fe80::3efd:feff:fea0:fbc1', 'type': '8086:1583', 'port': <net_device.NetDevice object at 0x7f5c8f571950>}
DTS_DUT_CMD: [192.168.0.34] {'intf': 'eth7', 'mac': '3c:fd:fe:a0:fb:c2', 'pci': '0000:02:00.2', 'numa': -1, 'ipv6': 'fe80::3efd:feff:fea0:fbc2', 'type': '8086:1583', 'port': <net_device.NetDevice object at 0x7f5c8f571a50>}
DTS_DUT_CMD: [192.168.0.34] {'intf': 'eth8', 'mac': '3c:fd:fe:a0:fb:c3', 'pci': '0000:02:00.3', 'numa': -1, 'ipv6': 'fe80::3efd:feff:fea0:fbc3', 'type': '8086:1583', 'port': <net_device.NetDevice object at 0x7f5c8f571150>}
INFO:
TARGET x86_64-native-linuxapp-gcc
DTS_DUT_CMD: [192.168.0.34] export RTE_TARGET=x86_64-native-linuxapp-gcc
DTS_DUT_CMD: [192.168.0.34] export RTE_SDK=`pwd`
DTS_DUT_CMD: [192.168.0.34] rm -rf x86_64-native-linuxapp-gcc
DTS_DUT_CMD: [192.168.0.34] rm -rf ./app/test/test_resource_c.res.o
DTS_DUT_CMD: [192.168.0.34] rm -rf ./app/test/test_resource_tar.res.o
DTS_DUT_CMD: [192.168.0.34] rm -rf ./app/test/test_pci_sysfs.res.o
DTS_DUT_CMD: [192.168.0.34] make -j install T=x86_64-native-linuxapp-gcc
DTS_DUT_CMD: [192.168.0.34] awk '/Hugepagesize/ {print $2}' /proc/meminfo
DTS_DUT_CMD: [192.168.0.34] awk '/Hugepagesize/ {print $2}' /proc/meminfo
DTS_DUT_CMD: [192.168.0.34] echo 4096 > /sys/kernel/mm/hugepages/hugepages-2048kB/nr_hugepages
DTS_DUT_CMD: [192.168.0.34] umount `awk '/hugetlbfs/ { print $2 }' /proc/mounts`
DTS_DUT_CMD: [192.168.0.34] awk '/hugetlbfs/ { print $2 }' /proc/mounts
DTS_DUT_CMD: [192.168.0.34] mkdir -p /mnt/huge
DTS_DUT_CMD: [192.168.0.34] mount -t hugetlbfs nodev /mnt/huge
DTS_DUT_CMD: [192.168.0.34] cat /proc/mounts |grep hugetlbfs
DTS_DUT_CMD: [192.168.0.34] modprobe uio
DTS_DUT_CMD: [192.168.0.34] lsmod | grep igb_uio
DTS_DUT_CMD: [192.168.0.34] insmod ./x86_64-native-linuxapp-gcc/kmod/igb_uio.ko
DTS_DUT_CMD: [192.168.0.34] lsmod | grep igb_uio
DTS_DUT_CMD: [192.168.0.34] usertools/dpdk-devbind.py --bind=igb_uio 0000:02:00.0 0000:02:00.1 0000:02:00.2 0000:02:00.3
INFO:
TEST SUITE : TestL2fwd
INFO: NIC : fortville_spirit
DTS_DUT_RESULT: [192.168.0.34] NUMA not supported
SUITE_DUT_CMD: [192.168.0.34] rm -rf ./app/test/test_resource_c.res.o
SUITE_DUT_CMD: [192.168.0.34] rm -rf ./app/test/test_resource_tar.res.o
SUITE_DUT_CMD: [192.168.0.34] rm -rf ./app/test/test_pci_sysfs.res.o
SUITE_DUT_CMD: [192.168.0.34] make -j -C ./examples/l2fwd
INFO: Test Case test_l2fwd_integrity Begin
SUITE_DUT_CMD: [192.168.0.34] ./examples/l2fwd/build/app/l2fwd -n 4 -c 0xf -- -q 1 -p 0x3 &
ERROR: Test Case test_l2fwd_integrity Result FAILED: TIMEOUT on ./examples/l2fwd/build/app/l2fwd -n 4 -c 0xf -- -q 1 -p 0x3 &
ERROR: [1] 25652
[PEXPECT]# EAL: Detected 8 lcore(s)
EAL: No free hugepages reported in hugepages-1048576kB
EAL: Probing VFIO support...
EAL: PCI device 0000:02:00.0 on NUMA socket -1
EAL: probe driver: 8086:1583 net_i40e
EAL: PCI device 0000:02:00.1 on NUMA socket -1
EAL: probe driver: 8086:1583 net_i40e
EAL: PCI device 0000:02:00.2 on NUMA socket -1
EAL: probe driver: 8086:1583 net_i40e
EAL: PCI device 0000:02:00.3 on NUMA socket -1
EAL: probe driver: 8086:1583 net_i40e
MAC updating enabled
EAL: Error - exiting with code: 1
Cause: No Ethernet ports - bye
INFO:
TEST SUITE ENDED: TestL2fwd
DTS_TESTER_CMD: modprobe igb
DTS_TESTER_CMD: modprobe ixgbe
DTS_TESTER_CMD: modprobe e1000e
DTS_TESTER_CMD: modprobe e1000
DTS_TESTER_CMD: ifconfig eno1 up
DTS_TESTER_CMD: ifconfig enp1s0f0 up
DTS_TESTER_CMD: ifconfig enp1s0f1 up
DTS_TESTER_CMD: ifconfig enp2s0f0 up
DTS_TESTER_CMD: ifconfig enp2s0f1 up
DTS_DUT_CMD: [192.168.0.34] echo 0000:02:00.0 > /sys/bus/pci/devices/0000\:02\:00.0/driver/unbind
DTS_DUT_CMD: [192.168.0.34] modprobe i40e
DTS_DUT_CMD: [192.168.0.34] echo 0000:02:00.0 > /sys/bus/pci/drivers/i40e/bind
DTS_DUT_CMD: [192.168.0.34] ifconfig eth6 up
DTS_DUT_CMD: [192.168.0.34] echo 0000:02:00.1 > /sys/bus/pci/devices/0000\:02\:00.1/driver/unbind
DTS_DUT_CMD: [192.168.0.34] modprobe i40e
DTS_DUT_CMD: [192.168.0.34] echo 0000:02:00.1 > /sys/bus/pci/drivers/i40e/bind
DTS_DUT_CMD: [192.168.0.34] ifconfig eth5 up
DTS_DUT_CMD: [192.168.0.34] echo 0000:02:00.2 > /sys/bus/pci/devices/0000\:02\:00.2/driver/unbind
DTS_DUT_CMD: [192.168.0.34] modprobe i40e
DTS_DUT_CMD: [192.168.0.34] echo 0000:02:00.2 > /sys/bus/pci/drivers/i40e/bind
DTS_DUT_CMD: [192.168.0.34] ifconfig eth7 up
DTS_DUT_CMD: [192.168.0.34] echo 0000:02:00.3 > /sys/bus/pci/devices/0000\:02\:00.3/driver/unbind
DTS_DUT_CMD: [192.168.0.34] modprobe i40e
DTS_DUT_CMD: [192.168.0.34] echo 0000:02:00.3 > /sys/bus/pci/drivers/i40e/bind
DTS_DUT_CMD: [192.168.0.34] ifconfig eth8 up
INFO: DTS ended
> On Dec 15, 2016, at 9:00 AM, Liu, Yong <yong.liu at intel.com> wrote:
>
> John, thanks for your information.
>
>> -----Original Message-----
>> From: dts [mailto:dts-bounces at dpdk.org] On Behalf Of john miller
>> Sent: Thursday, December 15, 2016 12:23 AM
>> To: dts at dpdk.org
>> Subject: [dts] Minimum Tester/DUT configuration
>>
>>
>> Hi All,
>>
>> We have configured a tester and a DUT for DTS testing, both machines are 4
>> core systems, one running ubuntu 14.04 and the other ubuntu 16.04 OS's .
>> Before we plug our hardware into the tester we are trying to establish
>> ground truth using a 2 port Fortville eagle card in the tester and one in
>> the DUT. The DTS documentation indicates that a minimum system requires 4
>> ports so my first question is, can some of the tests run with a 2 port
>> configuration and is there any documentation that indicates which tests
>> require all 4 ports ? The basic tests like hello_world, timer, and
>> cmdline pass, but when we attempt run tests like l2fwd we get the
>> following error indicating that 4 ports are required.
>>
>
> Each case may have different requirements like port number, core number, some kinds of dpdk configuration etc.
> Most of cases only require 2 ports and four cores, some performance case like l3fwd required more cores and ports.
> Some simple case like hello just require few cores. There's no existing document for each case requirement by now.
> We have plan to add configuration for each case which can get these information.
>
> For l2fwd case, it required 2 ports and 4 cores on the DUT.
> Just from your log, look like dts did not scan out enough port which matched Fortville eagle device's ID.
>
>>
>> INFO:
>> TEST SUITE : TestL2fwd
>> INFO: NIC : fortville_eagle
>> ERROR: set_up_all failed:
>> Traceback (most recent call last):
>> File "/work/dts/framework/test_case.py", line 223, in execute_setup_all
>> self.set_up_all()
>> File "/work/dts/tests/TestSuite_l2fwd.py", line 66, in set_up_all
>> "Not enough ports for " + self.nic)
>> File "/work/dts/framework/test_case.py", line 146, in verify
>> raise VerifyFailure(description)
>> VerifyFailure: 'Not enough ports for fortville_eagle’
>>
>>
>>
>> Also the DPDK mutilprocess test documentation indicates that the test
>> should run with only 2 ports. However when we attempt to run we get the
>> following error. The error looks like it is a result of the test
>> attempting to use more lcores than are available on the DUT. Although i
>> could change the test script to avoid this, I would like to know if there
>> is a configuration parameter that i missed that should be set to the
>> number of cores on the DUT.
>>
>
> That's just what we want to enhance. Most of our cases run on Intel 2 socket platform, and has enough memory and cores.
> We just noticed that some platforms may not have enough resources as we have. Some of the cases have been modified for reduce requirements and some of them not.
> We will work on that continuously and you can directly send patch to make sure cases also work on your platform.
> When case configuration feature is done, I think it will be more easily to gadapt to different platforms.
>
>>
>> DTS_DUT_CMD:
>> [192.168.0.11] ./examples/multi_process/simple_mp/simple_mp/x86_64-native-
>> linuxapp-gcc/simple_mp -n 1 -c 0x6 --proc-type=primary
>> SUITE_DUT_CMD:
>> [192.168.0.11] ./examples/multi_process/simple_mp/simple_mp/x86_64-native-
>> linuxapp-gcc/simple_mp -n 1 -c 0x60000 --proc-type=secondary
>> ERROR: Test Case test_multiprocess_simple_mploadtest Result
>> FAILED: TIMEOUT on ./examples/multi_process/simple_mp/simple_mp/x86_64-
>> native-linuxapp-gcc/simple_mp -n 1 -c 0x60000 --proc-type=secondary
>> ERROR: EAL: Detected lcore 0 as core 0 on socket 0
>> EAL: Detected lcore 1 as core 1 on socket 0
>> EAL: Detected lcore 2 as core 2 on socket 0
>> EAL: Detected lcore 3 as core 3 on socket 0
>> EAL: Detected lcore 4 as core 0 on socket 0
>> EAL: Detected lcore 5 as core 1 on socket 0
>> EAL: Detected lcore 6 as core 2 on socket 0
>> EAL: Detected lcore 7 as core 3 on socket 0
>> EAL: Support maximum 128 logical core(s) by configuration.
>> EAL: Detected 8 lcore(s)
>> EAL: lcore 17 unavailable
>> EAL: invalid coremask
>>
>> Usage: ./examples/multi_process/simple_mp/simple_mp/x86_64-native-
>> linuxapp-gcc/simple_mp [options]
>>
>>
>>
>> Thank you,
>> -John
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://dpdk.org/ml/archives/dts/attachments/20170124/9441ab51/attachment.html>
More information about the dts
mailing list