[dts] [PATCH] test_plans: add ddp ppp l2tp test plan
Xueqin Lin
xueqin.lin at intel.com
Wed Sep 5 04:41:18 CEST 2018
From: "xueqin.lin" <xueqin.lin at intel.com>
Signed-off-by: Xueqin Lin <xueqin.lin at intel.com>
---
test_plans/ddp_ppp_l2tp_test_plan.rst | 1093 +++++++++++++++++++++++++++++++++
1 file changed, 1093 insertions(+)
create mode 100644 test_plans/ddp_ppp_l2tp_test_plan.rst
diff --git a/test_plans/ddp_ppp_l2tp_test_plan.rst b/test_plans/ddp_ppp_l2tp_test_plan.rst
new file mode 100644
index 0000000..18f2f9a
--- /dev/null
+++ b/test_plans/ddp_ppp_l2tp_test_plan.rst
@@ -0,0 +1,1093 @@
+.. Copyright (c) <2018>, Intel Corporation
+ All rights reserved.
+
+ Redistribution and use in source and binary forms, with or without
+ modification, are permitted provided that the following conditions
+ are met:
+
+ - Redistributions of source code must retain the above copyright
+ notice, this list of conditions and the following disclaimer.
+
+ - Redistributions in binary form must reproduce the above copyright
+ notice, this list of conditions and the following disclaimer in
+ the documentation and/or other materials provided with the
+ distribution.
+
+ - Neither the name of Intel Corporation nor the names of its
+ contributors may be used to endorse or promote products derived
+ from this software without specific prior written permission.
+
+ THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+ SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
+ HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
+ STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
+ ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
+ OF THE POSSIBILITY OF SUCH DAMAGE.
+
+===========================
+DDP PPPoE/L2TPv2/PPPoL2TPv2
+===========================
+
+Fortville supports PPPoE/L2TPv2/PPPoL2TPv2 new protocols after loading profile.
+For DDP introduction, please refer to ddp gtp or ddp mpls test plan.
+
+Requirements as below::
+ 1) RSS for PPPoE packets: without IP payload, using session id and source
+ MAC as hash input set. With IP payload, using IP addresses and L4 ports
+ as hash input set.
+ 2) Classification for non-multicast IP encapsulated to PPPoL2TP: using inner
+ 5-tuple as hash input set for RSS.
+ 3) Classification for multicast IP encapsulated to PPPoL2TP: assign packets
+ to specific queue according to inner dst IP address.
+
+Dynamic flow type mapping eliminates usage of number of hard-coded flow
+types in bulky if-else statements. For instance, when configure hash enable
+flags for RSS in i40e_config_hena() function and will make partitioning FVL
+in i40e PMD more scalable.
+
+I40e PCTYPEs are statically mapped to RTE_ETH_FLOW_* types in DPDK, defined in
+rte_eth_ctrl.h, flow types used to define ETH_RSS_* offload types in
+rte_ethdev.h. RTE_ETH_FLOW_MAX is defined now as 22, leaves 42 flow type
+unassigned.
+
+Ppp-oe-ol2tpv2.pkgo defines and supports below pctype packets, also could
+check the information using command "ddp get info <profile>" after loading
+the profile, left numbers are pctype values, right are supported packets::
+
+ 14: L2TPv2CTRL
+ 15: PPPoE IPV4
+ 16: PPPoE IPV6
+ 17: PPPoE
+ 18: PPPoL2TPv2 IPV4
+ 19: PPPoL2TPv2 IPV6
+ 20: PPPoL2TPv2
+ 21: L2TPv2PAY
+
+There are so many kinds of packets that we can't cover all pctype test
+scenarios, below test plan focuses on above requirements to illustrate usage,
+also could do similar test for other packets. Select flow types value between
+23 and 63, design pctype, flow type and default input set mapping as below::
+
+ +----------------------+------------+------------+----------------------------------+----------------------------------+
+ | Packet Type | PcTypes | Flow Types | Hash Input Set | FD Input Set |
+ +----------------------+------------+------------+----------------------------------+----------------------------------+
+ | L2TPv2CTL | 14 | 27 | MAC SA, Session ID | MAC SA, Session ID |
+ +----------------------+------------+------------+----------------------------------+----------------------------------+
+ | PPPoE IPV4 | 15 | 28 | IPv4 SA, IPv4 DA, S-Port, D-Port | IPv4 SA, IPv4 DA, S-Port, D-Port |
+ +----------------------+------------+------------+----------------------------------+----------------------------------+
+ | PPPoE IPV6 | 16 | 29 | IPv6 SA, IPv6 DA, S-Port, D-Port | IPv6 SA, IPv6 DA, S-Port, D-Port |
+ +----------------------+------------+------------+----------------------------------+----------------------------------+
+ | PPPoE | 17 | 30 | MAC SA, Session ID | MAC SA, Session ID |
+ +----------------------+------------+------------+----------------------------------+----------------------------------+
+ | PPPoL2TPv2 IPV4 | 18 | 23 | IPv4 SA, IPv4 DA, S-Port, D-Port | IPv4 SA, IPv4 DA, S-Port, D-Port |
+ +----------------------+------------+------------+----------------------------------+----------------------------------+
+ | PPPoL2TPv2 IPV6 | 19 | 24 | IPv6 SA, IPv6 DA, S-Port, D-Port | IPv6 SA, IPv6 DA, S-Port, D-Port |
+ +----------------------+------------+------------+----------------------------------+----------------------------------+
+ | PPPoL2TPv2 | 20 | 25 | MAC SA, Session ID | MAC SA, Session ID |
+ +----------------------+------------+------------+----------------------------------+----------------------------------+
+ | L2TPv2PAY | 21 | 26 | MAC SA, Session ID | MAC SA, Session ID |
+ +----------------------+------------+------------+----------------------------------+----------------------------------+
+
+
+Prerequisites
+=============
+
+1. Host PF in DPDK driver::
+
+ ./tools/dpdk-devbind.py -b igb_uio 81:00.0
+
+2. Start testpmd on host, set chained port topology mode, add txq/rxq to
+ enable multi-queues. If test PF flow director, need to add
+ --pkt-filter-mode=perfect on testpmd to enable flow director.
+ In general, PF's max queue is 64::
+
+ ./testpmd -c f -n 4 -- -i --port-topology=chained --txq=64 --rxq=64
+ --pkt-filter-mode=perfect
+
+Load/delete dynamic device personalization
+==========================================
+
+1. Stop testpmd port before loading profile::
+
+ testpmd > port stop all
+
+2. Load ppp-oe-ol2tpv2.pkgo file to the memory buffer, save original
+ configuration and return in the same buffer to the ppp-oe-ol2tpv2.bak
+ file::
+
+ testpmd > ddp add (port_id) /tmp/ppp-oe-ol2tpv2.pkgo,
+ /tmp/ppp-oe-ol2tpv2.bak
+
+3. Remove profile from the network adapter and restore original
+ configuration::
+
+ testpmd > ddp del (port_id) /tmp/ppp-oe-ol2tpv2.bak
+
+4. Start testpmd port::
+
+ testpmd > port start all
+
+Note:
+
+ Ppp-oe-ol2tpv2.pkgo profile has been released publicly. You could download
+ below version to do our regression relative test. Loading DDP profile is
+ the prerequisite for below RSS and flow director cases.
+ https://downloadcenter.intel.com/download/28040
+
+
+Test Case: RSS for PPPoE with default input set
+===============================================
+
+1. Check flow type to pctype mapping::
+
+ testpmd> show port 0 pctype mapping
+
+2. Update PPPoE PAY flow type id 30 to pcytpe id 17 mapping item::
+
+ testpmd> port config 0 pctype mapping update 17 30
+
+3. Check flow type to pctype mapping adds 17 this mapping
+
+4. Enable flow type id 30's RSS::
+
+ testpmd> port config all rss 30
+
+5. Start testpmd, set fwd rxonly, enable output print
+
+6. Default hash input set are MAC SA, session ID. Send sessionid
+ PPPoE PAY packet, check RSS could work, print PKT_RX_RSS_HASH::
+
+ p=Ether(src="3C:FD:FE:A3:A0:01", dst="4C:FD:FE:A3:A0:01")/
+ PPPoE(sessionid=0x7)
+
+7. Send different sessionid PPPoE PAY packet, check to receive packet from
+ different queue::
+
+ p=Ether(src="3C:FD:FE:A3:A0:01", dst="4C:FD:FE:A3:A0:01")/
+ PPPoE(sessionid=0x8)
+
+8. Send different source address PPPoE PAY packet, check to receive packet
+ from different queue::
+
+ p=Ether(src="3C:FD:FE:A3:A0:02", dst="4C:FD:FE:A3:A0:01")/
+ PPPoE(sessionid=0x7)
+
+9. Send different destination address PPPoE PAY packet, check to receive
+ packet from same queue::
+
+ p=Ether(src="3C:FD:FE:A3:A0:01", dst="4C:FD:FE:A3:A0:02")/
+ PPPoE(sessionid=0x7)
+
+
+Test Case: RSS for PPPoE Ipv4 with default input set
+====================================================
+
+1. Check flow type to pctype mapping::
+
+ testpmd> show port 0 pctype mapping
+
+2. Update PPPoE Ipv4 flow type id 28 to pcytpe id 15 mapping item::
+
+ testpmd> port config 0 pctype mapping update 15 28
+
+3. Check flow type to pctype mapping adds 15 this mapping
+
+4. Enable flow type id 28's RSS::
+
+ testpmd> port config all rss 28
+
+5. Start testpmd, set fwd rxonly, enable output print
+
+6. Default hash input set are IPv4 SA, IPv4 DA, sport, dport. Send PPPoE
+ IPv4 packet, check RSS could work, print PKT_RX_RSS_HASH::
+
+ p=Ether()/PPPoE(sessionid=0x7)/PPP(proto=0x21)/IP(src="1.1.1.1",
+ dst="2.2.2.2")/UDP(sport=4000,dport=8000)/Raw('x' * 20)
+
+7. Send different inner source, destination address, sport, dport PPPoE
+ IPv4 packets, check to receive packet from different queues::
+
+ p=Ether()/PPPoE(sessionid=0x7)/PPP(proto=0x21)/IP(src="1.1.1.2",
+ dst="2.2.2.2")/UDP(sport=4000,dport=8000)/Raw('x' * 20)
+ p=Ether()/PPPoE(sessionid=0x7)/PPP(proto=0x21)/IP(src="1.1.1.1",
+ dst="2.2.2.3")/UDP(sport=4000,dport=8000)/Raw('x' * 20)
+ p=Ether()/PPPoE(sessionid=0x7)/PPP(proto=0x21)/IP(src="1.1.1.1",
+ dst="2.2.2.2")/UDP(sport=4001,dport=8000)/Raw('x' * 20)
+ p=Ether()/PPPoE(sessionid=0x7)/PPP(proto=0x21)/IP(src="1.1.1.1",
+ dst="2.2.2.2")/UDP(sport=4000,dport=8001)/Raw('x' * 20)
+
+8. Send different sessionid PPPoE IPv4 packet, check to receive packet
+ from same queue::
+
+ p=Ether()/PPPoE(sessionid=0x8)/PPP(proto=0x21)/IP(src="1.1.1.1",
+ dst="2.2.2.2")/UDP(sport=4000,dport=8000)/Raw('x' * 20)
+
+
+Test Case: RSS for PPPoE IPv6 with default input set
+====================================================
+
+1. Check flow type to pctype mapping::
+
+ testpmd> show port 0 pctype mapping
+
+2. Update PPPoE IPv6 flow type id 29 to pcytpe id 16 mapping item::
+
+ testpmd> port config 0 pctype mapping update 16 29
+
+3. Check flow type to pctype mapping adds 16 this mapping
+
+4. Enable flow type id 29's RSS::
+
+ testpmd> port config all rss 29
+
+5. Start testpmd, set fwd rxonly, enable output print
+
+6. Default hash input set are IPv6 SA, IPv6 DA, sport, dport. Send PPPoE
+ IPv6 packet, check RSS could work, print PKT_RX_RSS_HASH::
+
+ p=Ether()/PPPoE(sessionid=0x7)/PPP(proto=0x57)/
+ IPv6(src="1001:0db8:85a3:0000:0000:8a2e:0370:0001",
+ dst="2001:0db8:85a3:0000:0000:8a2e:0370:0001")/
+ UDP(sport=4000,dport=8000)/Raw('x' * 20)
+
+7. Send different inner source, destination address, sport, dport PPPoE
+ IPv6 packets, check to receive packet from different queues::
+
+ p=Ether()/PPPoE(sessionid=0x7)/PPP(proto=0x57)/
+ IPv6(src="1001:0db8:85a3:0000:0000:8a2e:0370:0002",
+ dst="2001:0db8:85a3:0000:0000:8a2e:0370:0001")/
+ UDP(sport=4000,dport=8000)/Raw('x' * 20)
+ p=Ether()/PPPoE(sessionid=0x7)/PPP(proto=0x57)/
+ IPv6(src="1001:0db8:85a3:0000:0000:8a2e:0370:0001",
+ dst="2001:0db8:85a3:0000:0000:8a2e:0370:0002")/
+ UDP(sport=4000,dport=8000)/Raw('x' * 20)
+ p=Ether()/PPPoE(sessionid=0x7)/PPP(proto=0x57)/
+ IPv6(src="1001:0db8:85a3:0000:0000:8a2e:0370:0001",
+ dst="2001:0db8:85a3:0000:0000:8a2e:0370:0001")/
+ UDP(sport=4001,dport=8000)/Raw('x' * 20)
+ p=Ether()/PPPoE(sessionid=0x7)/PPP(proto=0x57)/
+ IPv6(src="1001:0db8:85a3:0000:0000:8a2e:0370:0001",
+ dst="2001:0db8:85a3:0000:0000:8a2e:0370:0001")/
+ UDP(sport=4000,dport=8001)/Raw('x' * 20)
+
+8. Send different sessionid PPPoE IPv6 packet, check to receive packet
+ from same queue::
+
+ p=Ether()/PPPoE(sessionid=0x8)/PPP(proto=0x57)/
+ IPv6(src="1001:0db8:85a3:0000:0000:8a2e:0370:0001",
+ dst="2001:0db8:85a3:0000:0000:8a2e:0370:0001")/
+ UDP(sport=4000,dport=8000)/Raw('x' * 20)
+
+
+Test Case: RSS for L2TPv2 PAY with default input set
+====================================================
+
+1. Check flow type to pctype mapping::
+
+ testpmd> show port 0 pctype mapping
+
+2. Update L2TP PAY flow type id 26 to pcytpe id 21 mapping item::
+
+ testpmd> port config 0 pctype mapping update 21 26
+
+3. Check flow type to pctype mapping adds 21 this mapping
+
+4. Enable flow type id 26's RSS::
+
+ testpmd> port config all rss 26
+
+5. Start testpmd, set fwd rxonly, enable output print
+
+6. Default hash input set are MAC SA, session ID. Send sessionid
+ L2TP PAY packet, check RSS could work, print PKT_RX_RSS_HASH::
+
+ p=Ether(src="3C:FD:FE:A3:A0:01", dst="4C:FD:FE:A3:A0:01")/IP()/
+ UDP(dport=1701, sport=1701)/L2TP(sessionid=0x7)/Raw('x' * 20)
+
+7. Send different sessionid L2TP PAY packet, check to receive packet from
+ different queue::
+
+ p=Ether(src="3C:FD:FE:A3:A0:01", dst="4C:FD:FE:A3:A0:01")/IP()/
+ UDP(dport=1701, sport=1701)/L2TP(sessionid=0x8)/Raw('x' * 20)
+
+8. Send different source address L2TP PAY packet, check to receive packet
+ from different queue::
+
+ p=Ether(src="3C:FD:FE:A3:A0:02", dst="4C:FD:FE:A3:A0:01")/IP()/
+ UDP(dport=1701, sport=1701)/L2TP(sessionid=0x7)/Raw('x' * 20)
+
+9. Send different destination address L2TP PAY packet, check to receive
+ packet from same queue::
+
+ p=Ether(src="3C:FD:FE:A3:A0:01", dst="4C:FD:FE:A3:A0:02")/IP()/
+ UDP(dport=1701, sport=1701)/L2TP(sessionid=0x7)/Raw('x' * 20)
+
+
+Test Case: RSS for PPPoE according to sessionid
+===============================================
+
+1. Check flow type to pctype mapping::
+
+ testpmd> show port 0 pctype mapping
+
+2. Update PPPoE PAY flow type id 30 to pcytpe id 17 mapping item::
+
+ testpmd> port config 0 pctype mapping update 17 30
+
+3. Check flow type to pctype mapping adds 17 this mapping
+
+4. Reset PPPoE hash input set configuration::
+
+ testpmd> port config 0 pctype 17 hash_inset clear all
+
+5. Sessionid word is 47, enable hash input set for sessionid::
+
+ testpmd> port config 0 pctype 17 hash_inset set field 47
+
+6. Enable flow type id 30's RSS::
+
+ testpmd> port config all rss 30
+
+7. Start testpmd, set fwd rxonly, enable output print
+
+8. Send sessionid PPPoE PAY packet, check RSS could work, print
+ PKT_RX_RSS_HASH::
+
+ p=Ether(src="3C:FD:FE:A3:A0:01", dst="4C:FD:FE:A3:A0:01")/
+ PPPoE(sessionid=0x7)
+
+9. Send different sessionid PPPoE PAY packet, check to receive packet from
+ different queue::
+
+ p=Ether(src="3C:FD:FE:A3:A0:01", dst="4C:FD:FE:A3:A0:01")/
+ PPPoE(sessionid=0x8)
+
+
+Test Case: RSS for PPPoE according to source address
+====================================================
+
+1. Check flow type to pctype mapping::
+
+ testpmd> show port 0 pctype mapping
+
+2. Update PPPoE PAY flow type id 30 to pcytpe id 17 mapping item::
+
+ testpmd> port config 0 pctype mapping update 17 30
+
+3. Check flow type to pctype mapping adds 17 this mapping
+
+4. Reset PPPoE hash input set configuration::
+
+ testpmd> port config 0 pctype 17 hash_inset clear all
+
+5. Source mac words are 3~5, enable hash input set for source IPv4::
+
+ testpmd> port config 0 pctype 17 hash_inset set field 3
+ testpmd> port config 0 pctype 17 hash_inset set field 4
+ testpmd> port config 0 pctype 17 hash_inset set field 5
+
+6. Enable flow type id 30's RSS::
+
+ testpmd> port config all rss 30
+
+7. Start testpmd, set fwd rxonly, enable output print
+
+8. Send source address PPPoE PAY packet, check RSS could work, print
+ PKT_RX_RSS_HASH::
+
+ p=Ether(src="3C:FD:FE:A3:A0:01", dst="4C:FD:FE:A3:A0:01")/
+ PPPoE(sessionid=0x7)
+
+9. Send different source address PPPoE packet, check to receive packet from
+ different queue::
+
+ p=Ether(src="3C:FD:FE:A3:A0:02", dst="4C:FD:FE:A3:A0:01")/
+ PPPoE(sessionid=0x7)
+
+10. Send different destination address PPPoE packet, check to receive packet
+ from same queue::
+
+ p=Ether(src="3C:FD:FE:A3:A0:01", dst="4C:FD:FE:A3:A0:02")/
+ PPPoE(sessionid=0x7)
+
+
+Test Case: RSS for PPPoL2TP IPv4 according to inner source IPv4
+===============================================================
+
+1. Check flow type to pctype mapping::
+
+ testpmd> show port 0 pctype mapping
+
+2. Update PPPoL2TP IPv4 flow type id 23 to pcytpe id 18 mapping item::
+
+ testpmd> port config 0 pctype mapping update 18 23
+
+3. Check flow type to pctype mapping adds 23 this mapping
+
+4. Reset PPPoL2TP IPv4 hash input set configuration::
+
+ testpmd> port config 0 pctype 18 hash_inset clear all
+
+5. Inner source IPv4 words are 15~16 , enable hash input set for them::
+
+ testpmd> port config 0 pctype 18 hash_inset set field 15
+ testpmd> port config 0 pctype 18 hash_inset set field 16
+
+6. Enable flow type id 23's RSS::
+
+ testpmd> port config all rss 23
+
+7. Start testpmd, set fwd rxonly, enable output print
+
+8. Send inner source IPv4 PPPoL2TP IPv4 packet, check RSS could work, print
+ PKT_RX_RSS_HASH::
+
+ p=Ether()/IP()/UDP(dport=1701, sport=1701)/PPP_L2TP(proto=0x0021)/
+ IP(src="1.1.1.1",dst="2.2.2.2")/UDP(sport=4000, dport=8000)/Raw('x' * 20)
+
+9. Send different inner source IPv4 PPPoL2TP IPv4 packet, check to receive
+ packet from different queue::
+
+ p=Ether()/IP()/UDP(dport=1701, sport=1701)/PPP_L2TP(proto=0x0021)/
+ IP(src="1.1.1.2",dst="2.2.2.2")/UDP(sport=4000, dport=8000)/Raw('x' * 20)
+
+10. Send different inner destination IP PPPoL2TP IPv4 packet, check to receive
+ packet from same queue::
+
+ p=Ether()/IP()/UDP(dport=1701, sport=1701)/PPP_L2TP(proto=0x0021)/
+ IP(src="1.1.1.1",dst="2.2.2.3")/UDP(sport=4000, dport=8000)/Raw('x' * 20)
+
+
+Test Case: RSS for PPPoL2TP IPv4 according to inner destination IPv4
+====================================================================
+
+1. Check flow type to pctype mapping::
+
+ testpmd> show port 0 pctype mapping
+
+2. Update PPPoL2TP IPv4 flow type id 23 to pcytpe id 18 mapping item::
+
+ testpmd> port config 0 pctype mapping update 18 23
+
+3. Check flow type to pctype mapping adds 23 this mapping
+
+4. Reset PPPoL2TP IPv4 hash input set configuration::
+
+ testpmd> port config 0 pctype 18 hash_inset clear all
+
+5. Inner destination IPv4 words are 27~28 , enable hash input set for them::
+
+ testpmd> port config 0 pctype 18 hash_inset set field 27
+ testpmd> port config 0 pctype 18 hash_inset set field 28
+
+6. Enable flow type id 23's RSS::
+
+ testpmd> port config all rss 23
+
+7. Start testpmd, set fwd rxonly, enable output print
+
+8. Send inner destination IPv4 PPPoL2TP IPv4 packet, check RSS could work, print
+ PKT_RX_RSS_HASH::
+
+ p=Ether()/IP()/UDP(dport=1701, sport=1701)/PPP_L2TP(proto=0x0021)/
+ IP(src="1.1.1.1",dst="2.2.2.2")/UDP(sport=4000, dport=8000)/Raw('x' * 20)
+
+9. Send different inner destination IPv4 PPPoL2TP IPv4 packet, check to receive
+ packet from different queue::
+
+ p=Ether()/IP()/UDP(dport=1701, sport=1701)/PPP_L2TP(proto=0x0021)/
+ IP(src="1.1.1.1",dst="2.2.2.3")/UDP(sport=4000, dport=8000)/Raw('x' * 20)
+
+10. Send different inner source IPv4 PPPoL2TP IPv4 packet, check to receive packet
+ from same queue::
+
+ p=Ether()/IP()/UDP(dport=1701, sport=1701)/PPP_L2TP(proto=0x0021)/
+ IP(src="1.1.1.2",dst="2.2.2.2")/UDP(sport=4000, dport=8000)/Raw('x' * 20)
+
+
+Test Case: RSS for PPPoL2TP IPv4 according to sport
+===================================================
+
+1. Check flow type to pctype mapping::
+
+ testpmd> show port 0 pctype mapping
+
+2. Update PPPoL2TP IPv4 flow type id 23 to pcytpe id 18 mapping item::
+
+ testpmd> port config 0 pctype mapping update 18 23
+
+3. Check flow type to pctype mapping adds 23 this mapping
+
+4. Reset PPPoL2TP IPv4 hash input set configuration::
+
+ testpmd> port config 0 pctype 18 hash_inset clear all
+
+5. Sport word is 29, enable hash input set for it::
+
+ testpmd> port config 0 pctype 18 hash_inset set field 29
+
+6. Enable flow type id 23's RSS::
+
+ testpmd> port config all rss 23
+
+7. Start testpmd, set fwd rxonly, enable output print
+
+8. Send sport PPPoL2TP IPv4 packet, check RSS could work, print
+ PKT_RX_RSS_HASH::
+
+ p=Ether()/IP()/UDP(dport=1701, sport=1701)/PPP_L2TP(proto=0x0021)/
+ IP(src="1.1.1.1",dst="2.2.2.2")/UDP(sport=4000, dport=8000)/Raw('x' * 20)
+
+9. Send different sport PPPoL2TP IPv4 packet, check to receive packet from
+ different queue::
+
+ p=Ether()/IP()/UDP(dport=1701, sport=1701)/PPP_L2TP(proto=0x0021)/
+ IP(src="1.1.1.1",dst="2.2.2.2")/UDP(sport=4001, dport=8000)/Raw('x' * 20)
+
+10. Send different dport PPPoL2TP IPv4 packet, check to receive packet from
+ same queue::
+
+ p=Ether()/IP()/UDP(dport=1701, sport=1701)/PPP_L2TP(proto=0x0021)/
+ IP(src="1.1.1.1",dst="2.2.2.2")/UDP(sport=4000, dport=8001)/Raw('x' * 20)
+
+
+Test Case: RSS for PPPoL2TP IPv4 according to dport
+===================================================
+
+1. Check flow type to pctype mapping::
+
+ testpmd> show port 0 pctype mapping
+
+2. Update PPPoL2TP IPv4 flow type id 23 to pcytpe id 18 mapping item::
+
+ testpmd> port config 0 pctype mapping update 18 23
+
+3. Check flow type to pctype mapping adds 23 this mapping
+
+4. Reset PPPoL2TP IPv4 hash input set configuration::
+
+ testpmd> port config 0 pctype 10 hash_inset clear all
+
+5. Dport word is 30, enable hash input set for it::
+
+ testpmd> port config 0 pctype 10 hash_inset set field 30
+
+6. Enable flow type id 23's RSS::
+
+ testpmd> port config all rss 23
+
+7. Start testpmd, set fwd rxonly, enable output print
+
+8. Send dport PPPoL2TP IPv4 packet, check RSS could work, print
+ PKT_RX_RSS_HASH::
+
+ p=Ether()/IP()/UDP(dport=1701, sport=1701)/PPP_L2TP(proto=0x0021)/
+ IP(src="1.1.1.1",dst="2.2.2.2")/UDP(sport=4000, dport=8000)/Raw('x' * 20)
+
+9. Send different dport PPPoL2TP IPv4 packet, check to receive packet from
+ different queue::
+
+ p=Ether()/IP()/UDP(dport=1701, sport=1701)/PPP_L2TP(proto=0x0021)/
+ IP(src="1.1.1.1",dst="2.2.2.2")/UDP(sport=4000, dport=8001)/Raw('x' * 20)
+
+10. Send different sport PPPoL2TP IPv4 packet, check to receive packet from
+ same queue::
+
+ p=Ether()/IP()/UDP(dport=1701, sport=1701)/PPP_L2TP(proto=0x0021)/
+ IP(src="1.1.1.1",dst="2.2.2.2")/UDP(sport=4001, dport=8000)/Raw('x' * 20)
+
+
+Test Case: Flow director for PPPoE with default input set
+=========================================================
+
+1. Check flow type to pctype mapping::
+
+ testpmd> show port 0 pctype mapping
+
+2. Update PPPoE PAY flow type id 30 to pcytpe id 17 mapping item::
+
+ testpmd> port config 0 pctype mapping update 17 30
+
+3. Start testpmd, set fwd rxonly, enable output print
+
+4. Send PPPoE packets, check to receive packet from queue 0::
+
+ p=Ether(src="3C:FD:FE:A3:A0:01", dst="4C:FD:FE:A3:A0:01")/
+ PPPoE(sessionid=0x7)
+
+5. Use scapy to generate PPPoE raw packet test_pppoe.raw,
+ source/destination address should be swapped in the template
+ and traffic packets::
+
+ a=Ether(dst="3C:FD:FE:A3:A0:01", src="4C:FD:FE:A3:A0:01")/
+ PPPoE(sessionid=0x7)
+
+6. Setup raw flow type filter for flow director, configured queue is random
+ queue between 0~63, such as 36::
+
+ testpmd> flow_director_filter 0 mode raw add flow 30 fwd queue 36 fd_id 1
+ packet test_pppoe.raw
+
+7. Send matched swapped traffic packet, check to receive packet from
+ configured queue 36::
+
+ p=Ether(src="3C:FD:FE:A3:A0:01", dst="4C:FD:FE:A3:A0:01")/
+ PPPoE(sessionid=0x7)
+
+8. Default flow director input set are MAC SA and session ID, send non-matched
+ SA, sessionid, check to receive packet from queue 0::
+
+ p=Ether(src="3C:FD:FE:A3:A0:02", dst="4C:FD:FE:A3:A0:01")/
+ PPPoE(sessionid=0x7)
+ p=Ether(src="3C:FD:FE:A3:A0:01", dst="4C:FD:FE:A3:A0:01")/
+ PPPoE(sessionid=0x8)
+
+9. Send non-matched MAC DA, check to receive packet from queue 36::
+
+ p=Ether(src="3C:FD:FE:A3:A0:01", dst="4C:FD:FE:A3:A0:02")/
+ PPPoE(sessionid=0x7)
+
+
+Test Case: Flow director for PPPoE IPv4 with default input set
+==============================================================
+
+1. Check flow type to pctype mapping::
+
+ testpmd> show port 0 pctype mapping
+
+2. Update PPPoE IPv4 flow type id 28 to pcytpe id 15 mapping item::
+
+ testpmd> port config 0 pctype mapping update 15 28
+
+3. Start testpmd, set fwd rxonly, enable output print
+
+4. Send PPPoE IPv4 packets, check to receive packet from queue 0::
+
+ p=Ether()/PPPoE(sessionid=0x7)/PPP(proto=0x21)/IP(src="1.1.1.1",
+ dst="2.2.2.2")/UDP(sport=4000,dport=8000)/Raw('x' * 20)
+
+5. Use scapy to generate PPPoE IPv4 raw packet test_pppoe.raw,
+ source/destination address and port should be swapped in the template
+ and traffic packets::
+
+ a=Ether()/PPPoE(sessionid=0x7)/PPP(proto=0x21)/IP(dst="1.1.1.1",
+ src="2.2.2.2")/UDP(dport=4000,sport=8000)/Raw('x' * 20)
+
+6. Setup raw flow type filter for flow director, configured queue is random
+ queue between 0~63, such as 36::
+
+ testpmd> flow_director_filter 0 mode raw add flow 28 fwd queue 36 fd_id 1
+ packet test_pppoe.raw
+
+7. Send matched swapped traffic packet, check to receive packet from
+ configured queue 36::
+
+ p=Ether()/PPPoE(sessionid=0x7)/PPP(proto=0x21)/IP(src="1.1.1.1",
+ dst="2.2.2.2")/UDP(sport=4000,dport=8000)/Raw('x' * 20)
+
+8. Send non-matched inner src IP, inner dst IP, sport, dport packets, check to
+ receive packet from queue 0::
+
+ p=Ether()/PPPoE(sessionid=0x7)/PPP(proto=0x21)/IP(src="1.1.1.2",
+ dst="2.2.2.2")/UDP(sport=4000,dport=8000)/Raw('x' * 20)
+ p=Ether()/PPPoE(sessionid=0x7)/PPP(proto=0x21)/IP(src="1.1.1.1",
+ dst="2.2.2.3")/UDP(sport=4000,dport=8000)/Raw('x' * 20)
+ p=Ether()/PPPoE(sessionid=0x7)/PPP(proto=0x21)/IP(src="1.1.1.1",
+ dst="2.2.2.2")/UDP(sport=4001,dport=8000)/Raw('x' * 20)
+ p=Ether()/PPPoE(sessionid=0x7)/PPP(proto=0x21)/IP(src="1.1.1.1",
+ dst="2.2.2.2")/UDP(sport=4000,dport=8001)/Raw('x' * 20)
+
+9. Send non-matched sessionid packets, check to receive packet from queue 36::
+
+ p=Ether()/PPPoE(sessionid=0x8)/PPP(proto=0x21)/IP(src="1.1.1.1",
+ dst="2.2.2.2")/UDP(sport=4000,dport=8000)/Raw('x' * 20)
+
+
+Test Case: Flow director for PPPoE IPv6 with default input set
+==============================================================
+
+1. Check flow type to pctype mapping::
+
+ testpmd> show port 0 pctype mapping
+
+2. Update PPPoE IPv6 flow type id 29 to pcytpe id 16 mapping item::
+
+ testpmd> port config 0 pctype mapping update 16 29
+
+3. Start testpmd, set fwd rxonly, enable output print
+
+4. Send PPPoE IPv6 packets, check to receive packet from queue 0::
+
+ p=Ether()/PPPoE(sessionid=0x7)/PPP(proto=0x57)/
+ IPv6(src="1001:0db8:85a3:0000:0000:8a2e:0370:0001",
+ dst="2001:0db8:85a3:0000:0000:8a2e:0370:0001")/
+ UDP(sport=4000,dport=8000)/Raw('x' * 20)
+
+5. Use scapy to generate PPPoE IPv4 raw packet test_pppoe.raw,
+ source/destination address and port should be swapped in the template
+ and traffic packets::
+
+ a=Ether()/PPPoE(sessionid=0x7)/PPP(proto=0x57)/
+ IPv6(dst="1001:0db8:85a3:0000:0000:8a2e:0370:0001",
+ src="2001:0db8:85a3:0000:0000:8a2e:0370:0001")/
+ UDP(dport=4000,sport=8000)/Raw('x' * 20)
+
+6. Setup raw flow type filter for flow director, configured queue is random
+ queue between 0~63, such as 36::
+
+ testpmd> flow_director_filter 0 mode raw add flow 29 fwd queue 36 fd_id 1
+ packet test_pppoe.raw
+
+7. Send matched swapped traffic packet, check to receive packet from
+ configured queue 36::
+
+ p=Ether()/PPPoE(sessionid=0x7)/PPP(proto=0x57)/
+ IPv6(src="1001:0db8:85a3:0000:0000:8a2e:0370:0001",
+ dst="2001:0db8:85a3:0000:0000:8a2e:0370:0001")/
+ UDP(sport=4000,dport=8000)/Raw('x' * 20)
+
+8. Send non-matched inner src IPv6, inner dst IPv6, sport, dport packets,
+ check to receive packet from queue 0::
+
+ p=Ether()/PPPoE(sessionid=0x7)/PPP(proto=0x57)/
+ IPv6(src="1001:0db8:85a3:0000:0000:8a2e:0370:0002",
+ dst="2001:0db8:85a3:0000:0000:8a2e:0370:0001")/
+ UDP(sport=4000,dport=8000)/Raw('x' * 20)
+ p=Ether()/PPPoE(sessionid=0x7)/PPP(proto=0x57)/
+ IPv6(src="1001:0db8:85a3:0000:0000:8a2e:0370:0001",
+ dst="2001:0db8:85a3:0000:0000:8a2e:0370:0002")/
+ UDP(sport=4000,dport=8000)/Raw('x' * 20)
+ p=Ether()/PPPoE(sessionid=0x7)/PPP(proto=0x57)/
+ IPv6(src="1001:0db8:85a3:0000:0000:8a2e:0370:0001",
+ dst="2001:0db8:85a3:0000:0000:8a2e:0370:0001")/
+ UDP(sport=4001,dport=8000)/Raw('x' * 20)
+ p=Ether()/PPPoE(sessionid=0x7)/PPP(proto=0x57)/
+ IPv6(src="1001:0db8:85a3:0000:0000:8a2e:0370:0001",
+ dst="2001:0db8:85a3:0000:0000:8a2e:0370:0001")/
+ UDP(sport=4000,dport=8001)/Raw('x' * 20)
+
+9. Send non-matched sessionid packets, check to receive packet from queue 36::
+
+ p=Ether()/PPPoE(sessionid=0x8)/PPP(proto=0x57)/
+ IPv6(src="1001:0db8:85a3:0000:0000:8a2e:0370:0001",
+ dst="2001:0db8:85a3:0000:0000:8a2e:0370:0001")/
+ UDP(sport=4000,dport=8000)/Raw('x' * 20)
+
+
+Test Case: Flow director for L2TPv2 PAY with default input set
+==============================================================
+
+1. Check flow type to pctype mapping::
+
+ testpmd> show port 0 pctype mapping
+
+2. Update L2TP PAY flow type id 26 to pcytpe id 21 mapping item::
+
+ testpmd> port config 0 pctype mapping update 21 26
+
+3. Start testpmd, set fwd rxonly, enable output print
+
+4. Send L2TP PAY packets, check to receive packet from queue 0::
+
+ p=Ether(src="3C:FD:FE:A3:A0:01", dst="4C:FD:FE:A3:A0:01")/IP()/
+ UDP(dport=1701, sport=1701)/L2TP(sessionid=0x7)/Raw('x' * 20)
+
+5. Use scapy to generate L2TP PAY raw packet test_l2tp.raw,
+ source/destination address should be swapped in the template
+ and traffic packets::
+
+ a=Ether(dst="3C:FD:FE:A3:A0:01", src="4C:FD:FE:A3:A0:01")/IP()/
+ UDP(dport=1701, sport=1701)/L2TP(sessionid=0x7)/Raw('x' * 20)
+
+6. Setup raw flow type filter for flow director, configured queue is random
+ queue between 0~63, such as 36::
+
+ testpmd> flow_director_filter 0 mode raw add flow 26 fwd queue 36 fd_id 1
+ packet test_l2tp.raw
+
+7. Send matched swapped traffic packet, check to receive packet from
+ configured queue 36::
+
+ p=Ether(src="3C:FD:FE:A3:A0:01", dst="4C:FD:FE:A3:A0:01")/IP()/
+ UDP(dport=1701, sport=1701)/L2TP(sessionid=0x7)/Raw('x' * 20)
+
+8. Default flow director input set are MAC SA and session ID, send non-matched
+ SA, sessionid, check to receive packet from queue 0::
+
+ p=Ether(src="3C:FD:FE:A3:A0:02", dst="4C:FD:FE:A3:A0:01")/IP()/
+ UDP(dport=1701, sport=1701)/L2TP(sessionid=0x7)/Raw('x' * 20)
+ p=Ether(src="3C:FD:FE:A3:A0:01", dst="4C:FD:FE:A3:A0:01")/IP()/
+ UDP(dport=1701, sport=1701)/L2TP(sessionid=0x8)/Raw('x' * 20)
+
+9. Send non-matched MAC DA, check to receive packet from queue 36::
+
+ p=Ether(src="3C:FD:FE:A3:A0:01", dst="4C:FD:FE:A3:A0:02")/IP()/
+ UDP(dport=1701, sport=1701)/L2TP(sessionid=0x7)/Raw('x' * 20)
+
+
+Test Case: Flow director for PPPoL2TP IPv4 with default input set
+=================================================================
+
+1. Check flow type to pctype mapping::
+
+ testpmd> show port 0 pctype mapping
+
+2. Update PPPoL2TP IPv4 flow type id 23 to pcytpe id 18 mapping item::
+
+ testpmd> port config 0 pctype mapping update 18 23
+
+3. Start testpmd, set fwd rxonly, enable output print
+
+4. Send PPPoL2TP IPv4 packets, check to receive packet from queue 0::
+
+ p=Ether()/IP()/UDP(dport=1701, sport=1701)/PPP_L2TP(proto=0x0021)/
+ IP(src="1.1.1.1",dst="2.2.2.2")/UDP(sport=4000, dport=8000)/Raw('x' * 20)
+
+5. Use scapy to generate PPPoL2TP IPv4 raw packet test_pppol2tp.raw,
+ source/destination address and port should be swapped in the template
+ and traffic packets::
+
+ a=Ether()/IP()/UDP(dport=1701, sport=1701)/PPP_L2TP(proto=0x0021)/
+ IP(dst="1.1.1.1",src="2.2.2.2")/UDP(dport=4000, sport=8000)/Raw('x' * 20)
+
+6. Setup raw flow type filter for flow director, configured queue is random
+ queue between 0~63, such as 36::
+
+ testpmd> flow_director_filter 0 mode raw add flow 23 fwd queue 36 fd_id 1
+ packet test_pppol2tp.raw
+
+7. Send matched swapped traffic packet, check to receive packet from
+ configured queue 36::
+
+ p=Ether()/IP()/UDP(dport=1701, sport=1701)/PPP_L2TP(proto=0x0021)/
+ IP(src="1.1.1.1",dst="2.2.2.2")/UDP(sport=4000, dport=8000)/Raw('x' * 20)
+
+8. Send non-matched inner src IP, inner dst IP, sport, dport packets, check to
+ receive packet from queue 0::
+
+ p=Ether()/IP()/UDP(dport=1701, sport=1701)/PPP_L2TP(proto=0x0021)/
+ IP(src="1.1.1.2",dst="2.2.2.2")/UDP(sport=4000, dport=8000)/Raw('x' * 20)
+ p=Ether()/IP()/UDP(dport=1701, sport=1701)/PPP_L2TP(proto=0x0021)/
+ IP(src="1.1.1.1",dst="2.2.2.3")/UDP(sport=4000, dport=8000)/Raw('x' * 20)
+ p=Ether()/IP()/UDP(dport=1701, sport=1701)/PPP_L2TP(proto=0x0021)/
+ IP(src="1.1.1.1",dst="2.2.2.2")/UDP(sport=4001, dport=8000)/Raw('x' * 20)
+ p=Ether()/IP()/UDP(dport=1701, sport=1701)/PPP_L2TP(proto=0x0021)/
+ IP(src="1.1.1.1",dst="2.2.2.2")/UDP(sport=4000, dport=8001)/Raw('x' * 20)
+
+
+Test Case: Flow director for PPPoL2TP IPv6 with default input set
+=================================================================
+
+1. Check flow type to pctype mapping::
+
+ testpmd> show port 0 pctype mapping
+
+2. Update PPPoL2TP IPv6 flow type id 24 to pcytpe id 19 mapping item::
+
+ testpmd> port config 0 pctype mapping update 19 24
+
+3. Start testpmd, set fwd rxonly, enable output print
+
+4. Send PPPoL2TP IPv6 packets, check to receive packet from queue 0::
+
+ p=Ether()/IP()/UDP(dport=1701, sport=1701)/PPP_L2TP(proto=0x0057)/
+ IPv6(src="1001:0db8:85a3:0000:0000:8a2e:0370:0001",
+ dst="2001:0db8:85a3:0000:0000:8a2e:0370:0001")/
+ UDP(sport=4000, dport=8000)/Raw('x' * 20)
+
+5. Use scapy to generate PPPoL2TP IPv6 raw packet test_pppol2tp.raw,
+ source/destination address and port should be swapped in the template
+ and traffic packets::
+
+ a=Ether()/IP()/UDP(dport=1701, sport=1701)/PPP_L2TP(proto=0x0057)/
+ IPv6(dst="1001:0db8:85a3:0000:0000:8a2e:0370:0001",
+ src="2001:0db8:85a3:0000:0000:8a2e:0370:0001")/
+ UDP(dport=4000, sport=8000)/Raw('x' * 20)
+
+6. Setup raw flow type filter for flow director, configured queue is random
+ queue between 0~63, such as 36::
+
+ testpmd> flow_director_filter 0 mode raw add flow 24 fwd queue 36
+ fd_id 1 packet test_pppol2tp.raw
+
+7. Send matched swapped traffic packet, check to receive packet from
+ configured queue 36::
+
+ p=Ether()/IP()/UDP(dport=1701, sport=1701)/PPP_L2TP(proto=0x0057)/
+ IPv6(src="1001:0db8:85a3:0000:0000:8a2e:0370:0001",
+ dst="2001:0db8:85a3:0000:0000:8a2e:0370:0001")/
+ UDP(sport=4000, dport=8000)/Raw('x' * 20)
+
+8. Send non-matched inner src IPv6, inner dst IPv6, sport, dport packets,
+ check to receive packet from queue 0::
+ p=Ether()/IP()/UDP(dport=1701, sport=1701)/PPP_L2TP(proto=0x0057)/
+ IPv6(src="1001:0db8:85a3:0000:0000:8a2e:0370:0002",
+ dst="2001:0db8:85a3:0000:0000:8a2e:0370:0001")/
+ UDP(sport=4000, dport=8000)/Raw('x' * 20)
+ p=Ether()/IP()/UDP(dport=1701, sport=1701)/PPP_L2TP(proto=0x0057)/
+ IPv6(src="1001:0db8:85a3:0000:0000:8a2e:0370:0001",
+ dst="2001:0db8:85a3:0000:0000:8a2e:0370:0002")/
+ UDP(sport=4000, dport=8000)/Raw('x' * 20)
+ p=Ether()/IP()/UDP(dport=1701, sport=1701)/PPP_L2TP(proto=0x0057)/
+ IPv6(src="1001:0db8:85a3:0000:0000:8a2e:0370:0001",
+ dst="2001:0db8:85a3:0000:0000:8a2e:0370:0001")/
+ UDP(sport=4001, dport=8000)/Raw('x' * 20)
+ p=Ether()/IP()/UDP(dport=1701, sport=1701)/PPP_L2TP(proto=0x0057)/
+ IPv6(src="1001:0db8:85a3:0000:0000:8a2e:0370:0001",
+ dst="2001:0db8:85a3:0000:0000:8a2e:0370:0001")/
+ UDP(sport=4000, dport=8001)/Raw('x' * 20)
+
+
+Test Case: Flow director for PPPoL2TP IPv4 according to inner destination IPv4
+==============================================================================
+
+1. Check flow type to pctype mapping::
+
+ testpmd> show port 0 pctype mapping
+
+2. Update PPPoL2TP IPv4 flow type id 23 to pcytpe id 18 mapping item::
+
+ testpmd> port config 0 pctype mapping update 18 23
+
+3. Reset PPPoL2TP IPv4 flow director input set configuration::
+
+ testpmd> port config 0 pctype 18 fdir_inset clear all
+
+4. Inner dst IP words are 27 and 28, enable flow director input set
+ for them::
+
+ testpmd> port config 0 pctype 18 fdir_inset set field 27
+ testpmd> port config 0 pctype 18 fdir_inset set field 28
+
+5. Start testpmd, set fwd rxonly, enable output print
+
+6. Send PPPoL2TP IPv4 packets, check to receive packet from queue 0::
+
+ p=Ether()/IP()/UDP(dport=1701, sport=1701)/PPP_L2TP(proto=0x0021)/
+ IP(src="1.1.1.1",dst="2.2.2.2")/UDP(sport=4000, dport=8000)/Raw('x' * 20)
+
+7. Use scapy to generate PPPoL2TP IPv4 raw packet test_pppol2tp.raw,
+ source/destination address and port should be swapped in the template
+ and traffic packets::
+
+ a=Ether()/IP()/UDP(dport=1701, sport=1701)/PPP_L2TP(proto=0x0021)/
+ IP(dst="1.1.1.1",src="2.2.2.2")/UDP(dport=4000, sport=8000)/Raw('x' * 20)
+
+8. Setup raw flow type filter for flow director, configured queue is random
+ queue between 0~63, such as 36::
+
+ testpmd> flow_director_filter 0 mode raw add flow 23 fwd queue 36
+ fd_id 1 packet test_pppol2tp.raw
+
+9. Send matched swapped traffic packet, check to receive packet from
+ configured queue 36::
+
+ p=Ether()/IP()/UDP(dport=1701, sport=1701)/PPP_L2TP(proto=0x0021)/
+ IP(src="1.1.1.1",dst="2.2.2.2")/UDP(sport=4000, dport=8000)/Raw('x' * 20)
+
+10. Send matched inner dst IP, but non-matched inner src IP, sport,
+ dport packets, check to receive packet from queue 36::
+
+ p=Ether()/IP()/UDP(dport=1701, sport=1701)/PPP_L2TP(proto=0x0021)/
+ IP(src="1.1.1.2",dst="2.2.2.2")/UDP(sport=4000, dport=8000)/Raw('x' * 20)
+ p=Ether()/IP()/UDP(dport=1701, sport=1701)/PPP_L2TP(proto=0x0021)/
+ IP(src="1.1.1.1",dst="2.2.2.2")/UDP(sport=4001, dport=8000)/Raw('x' * 20)
+ p=Ether()/IP()/UDP(dport=1701, sport=1701)/PPP_L2TP(proto=0x0021)/
+ IP(src="1.1.1.1",dst="2.2.2.2")/UDP(sport=4000, dport=8001)/Raw('x' * 20)
+
+11. Send non-matched inner dst IP packets, check to receive packet from
+ queue 0::
+
+ p=Ether()/IP()/UDP(dport=1701, sport=1701)/PPP_L2TP(proto=0x0021)/
+ IP(src="1.1.1.1",dst="2.2.2.3")/UDP(sport=4000, dport=8000)/Raw('x' * 20)
+
+
+Test Case: Flow director for PPPoL2TP IPv6 according to inner destination IPv6
+==============================================================================
+
+1. Check flow type to pctype mapping::
+
+ testpmd> show port 0 pctype mapping
+
+2. Update PPPoL2TP IPv6 flow type id 24 to pcytpe id 19 mapping item::
+
+ testpmd> port config 0 pctype mapping update 19 24
+
+3. Reset PPPoL2TP IPv6 flow director input set configuration::
+
+ testpmd> port config 0 pctype 19 fdir_inset clear all
+
+4. Inner dst IPv6 words are 21~28, enable flow director input set
+ for them::
+
+ testpmd> port config 0 pctype 19 fdir_inset set field 21
+ testpmd> port config 0 pctype 19 fdir_inset set field 22
+ testpmd> port config 0 pctype 19 fdir_inset set field 23
+ testpmd> port config 0 pctype 19 fdir_inset set field 24
+ testpmd> port config 0 pctype 19 fdir_inset set field 25
+ testpmd> port config 0 pctype 19 fdir_inset set field 26
+ testpmd> port config 0 pctype 19 fdir_inset set field 27
+ testpmd> port config 0 pctype 19 fdir_inset set field 28
+
+5. Start testpmd, set fwd rxonly, enable output print
+
+6. Send PPPoL2TP IPv6 packets, check to receive packet from queue 0::
+
+ p=Ether()/IP()/UDP(dport=1701, sport=1701)/PPP_L2TP(proto=0x0057)/
+ IPv6(src="1001:0db8:85a3:0000:0000:8a2e:0370:0001",
+ dst="2001:0db8:85a3:0000:0000:8a2e:0370:0001")/
+ UDP(sport=4000, dport=8000)/Raw('x' * 20)
+
+7. Use scapy to generate PPPoL2TP IPv6 raw packet test_pppol2tp.raw,
+ source/destination address and port should be swapped in the template
+ and traffic packets::
+
+ a=Ether()/IP()/UDP(dport=1701, sport=1701)/PPP_L2TP(proto=0x0057)/
+ IPv6(dst="1001:0db8:85a3:0000:0000:8a2e:0370:0001",
+ src="2001:0db8:85a3:0000:0000:8a2e:0370:0001")/
+ UDP(dport=4000, sport=8000)/Raw('x' * 20)
+
+8. Setup raw flow type filter for flow director, configured queue is random
+ queue between 0~63, such as 36::
+
+ testpmd> flow_director_filter 0 mode raw add flow 24 fwd queue 36
+ fd_id 1 packet test_pppol2tp.raw
+
+9. Send matched swapped traffic packet, check receive packet from
+ configured queue 36::
+
+ p=Ether()/IP()/UDP(dport=1701, sport=1701)/PPP_L2TP(proto=0x0057)/
+ IPv6(src="1001:0db8:85a3:0000:0000:8a2e:0370:0001",
+ dst="2001:0db8:85a3:0000:0000:8a2e:0370:0001")/
+ UDP(sport=4000, dport=8000)/Raw('x' * 20)
+
+10. Send matched inner dst IPv6, but non-matched inner src IPv6,
+ sport, dport packets, check to receive packet from queue 36::
+
+ p=Ether()/IP()/UDP(dport=1701, sport=1701)/PPP_L2TP(proto=0x0057)/
+ IPv6(src="1001:0db8:85a3:0000:0000:8a2e:0370:0002",
+ dst="2001:0db8:85a3:0000:0000:8a2e:0370:0001")/
+ UDP(sport=4000, dport=8000)/Raw('x' * 20)
+ p=(Ether()/IP()/UDP(dport=1701, sport=1701)/PPP_L2TP(proto=0x0057)/
+ IPv6(src="1001:0db8:85a3:0000:0000:8a2e:0370:0001",
+ dst="2001:0db8:85a3:0000:0000:8a2e:0370:0001")/
+ UDP(sport=4001, dport=8000)/Raw('x' * 20)
+ p=Ether()/IP()/UDP(dport=1701, sport=1701)/PPP_L2TP(proto=0x0057)/
+ IPv6(src="1001:0db8:85a3:0000:0000:8a2e:0370:0001",
+ dst="2001:0db8:85a3:0000:0000:8a2e:0370:0001")/
+ UDP(sport=4000, dport=8001)/Raw('x' * 20)
+
+11. Send non-matched inner dst IPv6 packets, check to receive packet
+ from queue 0::
+
+ p=Ether()/IP()/UDP(dport=1701, sport=1701)/PPP_L2TP(proto=0x0057)/
+ IPv6(src="1001:0db8:85a3:0000:0000:8a2e:0370:0001",
+ dst="2001:0db8:85a3:0000:0000:8a2e:0370:0002")/
+ UDP(sport=4000, dport=8000)/Raw('x' * 20)
+
--
2.7.5
More information about the dts
mailing list