[dts] [PATCH V2] test_plans/scatter: test plan revise
Tu, Lijuan
lijuan.tu at intel.com
Mon Apr 15 23:09:19 CEST 2019
Applied with format changed.
> -----Original Message-----
> From: dts [mailto:dts-bounces at dpdk.org] On Behalf Of Zhe
> Sent: Thursday, April 11, 2019 9:01 AM
> To: dts at dpdk.org
> Cc: Wan, Zhe <zhe.wan at intel.com>
> Subject: [dts] [PATCH V2] test_plans/scatter: test plan revise
>
> From: Zhe Wan <zhe.wan at intel.com>
>
> Signed-off-by: Zhe Wan <zhe.wan at intel.com>
> ---
> test_plans/scatter_test_plan.rst | 30 ++++++++++++++++--------------
> 1 file changed, 16 insertions(+), 14 deletions(-)
>
> diff --git a/test_plans/scatter_test_plan.rst
> b/test_plans/scatter_test_plan.rst
> index cf5e1e5..a7c337b 100644
> --- a/test_plans/scatter_test_plan.rst
> +++ b/test_plans/scatter_test_plan.rst
> @@ -72,15 +72,15 @@ the CRC from the packet before returning it.
> As a whole, the following packet lengths (CRC included) must be tested to
> check all packet memory configurations:
>
> -#. packet length < mbuf data buffer size
> +1) packet length < mbuf data buffer size
>
> -#. packet length = mbuf data buffer size
> +2) packet length = mbuf data buffer size
>
> -#. packet length = mbuf data buffer size + 1
> +3) packet length = mbuf data buffer size + 1
>
> -#. packet length = mbuf data buffer size + 4
> +4) packet length = mbuf data buffer size + 4
>
> -#. packet length = mbuf data buffer size + 5
> +5) packet length = mbuf data buffer size + 5
>
> In cases 1) and 2), the hardware RX engine stores the packet data and the
> CRC in a single buffer.
> @@ -101,21 +101,23 @@ Assuming that ports ``0`` and ``1`` of the test
> target are directly connected to a Traffic Generator, launch the ``testpmd``
> application with the following
> arguments::
>
> - ./build/app/testpmd -cffffff -n 3 -- -i --rxd=1024 --txd=1024 \
> - --burst=144 --txpt=32 --txht=8 --txwt=8 --txfreet=0 --rxfreet=64 \
> - --mbcache=200 --portmask=0x3 --mbuf-size=1024
> + ./x86_64-native-linuxapp-gcc/app/testpmd -c 0x6 -n 4 -- -i
> + --mbcache=200 \
> + --mbuf-size=2048 --portmask=0x1 --max-pkt-len=9000
> + --port-topology=loop \ --tx-offloads=DEV_TX_OFFLOAD_MULTI_SEGS
>
> The -n command is used to select the number of memory channels. It
> should match the number of memory channels on that setup.
>
> -Setting the size of the mbuf data buffer to 1024 makes 1025-bytes input
> packets -(CRC included) and larger packets to be stored in two buffers by the
> hardware -RX engine.
> +DEV_TX_OFFLOAD_MULTI_SEGS is a TX offload capability, means device
> +supports multi segment send. Defined in DPDK code
> lib/librte_ethdev/rte_ethdev.h.
>
> -Test Case: Mbuf 1024 traffic
> +#define DEV_TX_OFFLOAD_MULTI_SEGS 0x00008000
> +
> +Test Case: Scatter Mbuf 2048
> ============================
>
> Start packet forwarding in the ``testpmd`` application with the ``start``
> command.
> -Send 5 packets of lengths (CRC included) 1023, 1024, 1025, 1028, and 1029.
> +Send 5 packets,the lengths are mbuf-size + offset (CRC included).
> +The offset are -1, 0, 1, 4, 5 respectively.
> Check that the same amount of frames and bytes are received back by the
> Traffic -Generator from its port connected to the target's port 1.
> +Generator from it's port connected to the target's port 1.
> --
> 1.8.3.1
More information about the dts
mailing list