[dts] [PATCH] test_plans: add case for loopback multi-queue test

[Tu, Lijuan]

Hi yiyan,

Applying: test_plans: add case for loopback multi-queue test
.git/rebase-apply/patch:293: new blank line at EOF.
+
warning: 1 line adds whitespace errors.

> -----Original Message-----
> From: dts [mailto:dts-bounces at dpdk.org] On Behalf Of Yinan
> Sent: Wednesday, February 27, 2019 9:07 AM
> To: dts at dpdk.org
> Cc: Wang, Yinan <yinan.wang at intel.com>
> Subject: [dts] [PATCH] test_plans: add case for loopback multi-queue test
> 
> From: Wang Yinan <yinan.wang at intel.com>
> 
>   add loopback_multi_queues_test_plan.rst
> ---
>  .../loopback_multi_queues_test_plan.rst       | 282 ++++++++++++++++++
>  1 file changed, 282 insertions(+)
>  create mode 100644 test_plans/loopback_multi_queues_test_plan.rst
> 
> diff --git a/test_plans/loopback_multi_queues_test_plan.rst
> b/test_plans/loopback_multi_queues_test_plan.rst
> new file mode 100644
> index 0000000..020438c
> --- /dev/null
> +++ b/test_plans/loopback_multi_queues_test_plan.rst
> @@ -0,0 +1,282 @@
> +.. Copyright (c) <2019>, Intel Corporation
> +   All rights reserved.
> +
> +   Redistribution and use in source and binary forms, with or without
> +   modification, are permitted provided that the following conditions
> +   are met:
> +
> +   - Redistributions of source code must retain the above copyright
> +     notice, this list of conditions and the following disclaimer.
> +
> +   - Redistributions in binary forim must reproduce the above copyright
> +     notice, this list of conditions and the following disclaimer in
> +     the documentation and/or other materials provided with the
> +     distribution.
> +
> +   - Neither the name of Intel Corporation nor the names of its
> +     contributors may be used to endorse or promote products derived
> +     from this software without specific prior written permission.
> +
> +   THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND
> CONTRIBUTORS
> +   "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
> +   LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
> +   FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
> +   COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT,
> INDIRECT,
> +   INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
> +   (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
> OR
> +   SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
> +   HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
> CONTRACT,
> +   STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
> +   ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
> +   OF THE POSSIBILITY OF SUCH DAMAGE.
> +
> +===========================================
> +Loopback virtio-user multi-queues Tests
> +===========================================
> +
> +Description
> +===========
> +
> +Benchmark vhost/virtio-user loopback multi-queues test with 7 RX/TX PATHs.
> +Includes Mergeable, Normal, Vector_RX, Inorder mergeable, Inorder
> +no-mergeable, Virtio 1.1 mergeable, Virtio 1.1 no-mergeable Path.
> +
> +Test Case 1: loopback 2 queues test with Virtio 1.1 mergeable path
> +================================================================
> =======
> +====
> +
> +1. Launch testpmd by below command::
> +
> +    rm -rf vhost-net*
> +    ./testpmd -c 0xe -n 4 --socket-mem 1024,1024 --no-pci \
> +    --vdev 'eth_vhost0,iface=vhost-net,queues=2' -- \
> +    -i --nb-cores=2 --rxq=2 --txq=2
> +    testpmd>set fwd mac
> +
> +2. Launch virtio-user by below command::
> +
> +    ./testpmd -n 4 -l 5-7 --socket-mem 1024,1024 \
> +    --legacy-mem --no-pci --file-prefix=virtio \
> +    --vdev=net_virtio_user0,mac=00:01:02:03:04:05,path=./vhost-
> net,queues=2,packed_vq=1,mrg_rxbuf=1 \
> +    -- -i --tx-offloads=0x0 --enable-hw-vlan-strip --rss-ip --nb-cores=2 --rxq=2 --
> txq=2
> +    >set fwd mac
> +    >start
> +
> +3. Send packets with vhost-testpmd,[frame_size] is the parameter changs in
> [64, 128, 256, 512, 1024, 1518]::
> +
> +    testpmd>set txpkts [frame_size]
> +    testpmd>start tx_first 32
> +    testpmd>start
> +
> +4. Get throughput 10 times and calculate the average throughput::
> +
> +    testpmd>show port stats all
> +
> +5. Check each queue's RX/TX packet numbers::
> +
> +    testpmd>stop
> +
> +Test Case 2: loopback 2 queues test with Virtio 1.1 no-mergeable path
> +================================================================
> =======
> +====
> +
> +1. Launch testpmd by below command::
> +
> +    rm -rf vhost-net*
> +    ./testpmd -c 0xe -n 4 --socket-mem 1024,1024 --no-pci \
> +    --vdev 'eth_vhost0,iface=vhost-net,queues=2' -- \
> +    -i --nb-cores=2 --rxq=2 --txq=2
> +    testpmd>set fwd mac
> +
> +2. Launch virtio-user by below command::
> +
> +    ./testpmd -n 4 -l 5-7 --socket-mem 1024,1024 \
> +    --legacy-mem --no-pci --file-prefix=virtio \
> +    --vdev=net_virtio_user0,mac=00:01:02:03:04:05,path=./vhost-
> net,queues=2,packed_vq=1,mrg_rxbuf=0 \
> +    -- -i --tx-offloads=0x0 --enable-hw-vlan-strip --rss-ip --nb-cores=2 --rxq=2 --
> txq=2
> +    >set fwd mac
> +    >start
> +
> +3. Send packets with vhost-testpmd,[frame_size] is the parameter changs in
> [64, 128, 256, 512, 1024, 1518]::
> +
> +    testpmd>set txpkts [frame_size]
> +    testpmd>start tx_first 32
> +    testpmd>start
> +
> +4. Get throughput 10 times and calculate the average throughput::
> +
> +    testpmd>show port stats all
> +
> +5. Check each queue's RX/TX packet numbers::
> +
> +    testpmd>stop
> +
> +Test Case 3: loopback 2 queues test with Inorder mergeable path
> +================================================================
> =======
> +====
> +
> +1. Launch testpmd by below command::
> +
> +    rm -rf vhost-net*
> +    ./testpmd -c 0xe -n 4 --socket-mem 1024,1024 --no-pci \
> +    --vdev 'eth_vhost0,iface=vhost-net,queues=2' -- \
> +    -i --nb-cores=2 --rxq=2 --txq=2
> +    testpmd>set fwd mac
> +
> +2. Launch virtio-user by below command::
> +
> +    ./testpmd -n 4 -l 5-7 --socket-mem 1024,1024 \
> +    --legacy-mem --no-pci --file-prefix=virtio \
> +    --vdev=net_virtio_user0,mac=00:01:02:03:04:05,path=./vhost-
> net,queues=2,in_order=1 \
> +    -- -i --tx-offloads=0x0 --enable-hw-vlan-strip --rss-ip --nb-cores=2 --rxq=2 --
> txq=2
> +    >set fwd mac
> +    >start
> +
> +3. Send packets with vhost-testpmd,[frame_size] is the parameter changs in
> [64, 128, 256, 512, 1024, 1518]::
> +
> +    testpmd>set txpkts [frame_size]
> +    testpmd>start tx_first 32
> +    testpmd>start
> +
> +4. Get throughput 10 times and calculate the average throughput::
> +
> +    testpmd>show port stats all
> +
> +5. Check each queue's RX/TX packet numbers::
> +
> +    testpmd>stop
> +
> +Test Case 4: loopback 2 queues test with Inorder no-mergeable path
> +================================================================
> =======
> +====
> +
> +1. Launch testpmd by below command::
> +
> +    rm -rf vhost-net*
> +    ./testpmd -c 0xe -n 4 --socket-mem 1024,1024 --no-pci \
> +    --vdev 'eth_vhost0,iface=vhost-net,queues=2' -- \
> +    -i --nb-cores=2 --rxq=2 --txq=2
> +    testpmd>set fwd mac
> +
> +2. Launch virtio-user by below command::
> +
> +    ./testpmd -n 4 -l 5-7 --socket-mem 1024,1024 \
> +    --legacy-mem --no-pci --file-prefix=virtio \
> +    --vdev=net_virtio_user0,mac=00:01:02:03:04:05,path=./vhost-
> net,in_order=1,queues=2,mrg_rxbuf=0 \
> +    -- -i --tx-offloads=0x0 --enable-hw-vlan-strip --rss-ip --nb-cores=2 --rxq=2 --
> txq=2
> +    >set fwd mac
> +    >start
> +
> +3. Send packets with vhost-testpmd,[frame_size] is the parameter changs in
> [64, 128, 256, 512, 1024, 1518]::
> +
> +    testpmd>set txpkts [frame_size]
> +    testpmd>start tx_first 32
> +    testpmd>start
> +
> +4. Get throughput 10 times and calculate the average throughput::
> +
> +    testpmd>show port stats all
> +
> +5. Check each queue's RX/TX packet numbers::
> +
> +    testpmd>stop
> +
> +Test Case 5: loopback 4 queues test with Mergeable path
> +================================================================
> =======
> +====
> +
> +1. Launch testpmd by below command::
> +
> +    rm -rf vhost-net*
> +    ./testpmd -l 2-6 -n 4 --socket-mem 1024,1024 --no-pci \
> +    --vdev 'eth_vhost0,iface=vhost-net,queues=4' -- \
> +    -i --nb-cores=4 --rxq=4 --txq=4
> +    testpmd>set fwd mac
> +
> +2. Launch virtio-user by below command::
> +
> +    ./testpmd -n 4 -l 7-11 --socket-mem 1024,1024 \
> +    --legacy-mem --no-pci --file-prefix=virtio \
> +    --vdev=net_virtio_user0,mac=00:01:02:03:04:05,path=./vhost-
> net,queues=4,in_order=0,mrg_rxbuf=1 \
> +    -- -i --tx-offloads=0x0 --enable-hw-vlan-strip --rss-ip --nb-cores=4 --rxq=4 --
> txq=4
> +    >set fwd mac
> +    >start
> +
> +3. Send packets with vhost-testpmd,[frame_size] is the parameter changs in
> [64, 128, 256, 512, 1024, 1518]::
> +
> +    testpmd>set txpkts [frame_size]
> +    testpmd>start tx_first 32
> +    testpmd>start
> +
> +4. Get throughput 10 times and calculate the average throughput::
> +
> +    testpmd>show port stats all
> +
> +5. Check each queue's RX/TX packet numbers::
> +
> +    testpmd>stop
> +
> +
> +Test Case 6: loopback 4 queues test with Normal path
> +================================================================
> =======
> +====
> +
> +1. Launch vhost by below command::
> +
> +    rm -rf vhost-net*
> +    ./testpmd -n 4 -l 2-6  --socket-mem 1024,1024 --legacy-mem --no-pci \
> +    --file-prefix=vhost --vdev 'net_vhost0,iface=vhost-net,queues=4' -- \
> +    -i --nb-cores=4 --rxq=4 --txq=4
> +    >set fwd mac
> +
> +2. Launch virtio-user by below command::
> +
> +    ./testpmd -n 4 -l 7-11 --socket-mem 1024,1024 \
> +    --legacy-mem --no-pci --file-prefix=virtio \
> +    --vdev=net_virtio_user0,mac=00:01:02:03:04:05,path=./vhost-
> net,queues=4,in_order=0,mrg_rxbuf=0 \
> +    -- -i --tx-offloads=0x0 --enable-hw-vlan-strip --rss-ip --nb-cores=4 --rxq=4 --
> txq=4
> +    >set fwd mac
> +    >start
> +
> +3. Send packets with vhost-testpmd,[frame_size] is the parameter changs in
> [64, 128, 256, 512, 1024, 1518]::
> +
> +    testpmd>set txpkts [frame_size]
> +    testpmd>start tx_first 32
> +    testpmd>start
> +
> +4. Get throughput 10 times and calculate the average throughput::
> +
> +    testpmd>show port stats all
> +
> +5. Check each queue's RX/TX packet numbers::
> +
> +    testpmd>stop
> +
> +Test Case 7: loopback test with Vector_RX path
> +================================================================
> =======
> +====
> +
> +1. Launch vhost by below command::
> +
> +    rm -rf vhost-net*
> +    ./testpmd -n 4 -l 2-6  --socket-mem 1024,1024 --legacy-mem --no-pci \
> +    --file-prefix=vhost --vdev 'net_vhost0,iface=vhost-net,queues=4' -- \
> +    -i --nb-cores=4 --rxq=4 --txq=4
> +    >set fwd mac
> +
> +2. Launch virtio-user by below command::
> +
> +    ./testpmd -n 4 -l 7-11 --socket-mem 1024,1024 \
> +    --legacy-mem --no-pci --file-prefix=virtio \
> +    --vdev=net_virtio_user0,mac=00:01:02:03:04:05,path=./vhost-
> net,queues=4,in_order=0,mrg_rxbuf=0 \
> +    -- -i --tx-offloads=0x0 --rss-ip --nb-cores=4 --rxq=4 --txq=4
> +    >set fwd mac
> +    >start
> +
> +3. Send packets with vhost-testpmd,[frame_size] is the parameter changs in
> [64, 128, 256, 512, 1024, 1518]::
> +
> +    testpmd>set txpkts [frame_size]
> +    testpmd>start tx_first 32
> +    testpmd>start
> +
> +4. Get throughput 10 times and calculate the average throughput::
> +
> +    testpmd>show port stats all
> +
> +5. Check each queue's RX/TX packet numbers::
> +
> +    testpmd>stop
> +
> --
> 2.17.1