[dts] [PATCH] test_plans: add a test case to test plan

[Tu, Lijuan]

Applying: test_plans: add a test case to test plan
error: patch failed: test_plans/vlan_test_plan.rst:100
error: test_plans/vlan_test_plan.rst: patch does not apply
Patch failed at 0001 test_plans: add a test case to test plan

> -----Original Message-----
> From: dts [mailto:dts-bounces at dpdk.org] On Behalf Of Peng Yuan
> Sent: Wednesday, June 26, 2019 5:40 PM
> To: dts at dpdk.org
> Cc: Peng, Yuan <yuan.peng at intel.com>
> Subject: [dts] [PATCH] test_plans: add a test case to test plan
> 
> Add a test case to vlan_test_plan.rst
> 
> Signed-off-by: Peng Yuan <yuan.peng at intel.com>
> 
> diff --git a/test_plans/vlan_test_plan.rst b/test_plans/vlan_test_plan.rst
> index 54df0b6..a5058f8 100644
> --- a/test_plans/vlan_test_plan.rst
> +++ b/test_plans/vlan_test_plan.rst
> @@ -76,7 +76,38 @@ The -n command is used to select the number of
> memory channels. It should match  Set the verbose level to 1 to display
> information for each received packet::
> 
>    testpmd> set verbose 1
> +  testpmd> vlan set filter on
> 
> +Test Case: Enable receipt of VLAN packets and disable VLAN header
> +stripping
> +===============================================================
> ========
> +====
> +
> +Setup the ``mac`` forwarding mode::
> +
> +  testpmd> set fwd mac
> +  Set mac packet forwarding mode
> +
> +Enable the receipt of VLAN packets with VLAN Tag Identifier 1 on port 0::
> +
> +  testpmd> rx_vlan add 1 0
> +  testpmd> vlan set strip off 0
> +  testpmd> start
> +    rxonly packet forwarding - CRC stripping disabled - packets/burst=32
> +    nb forwarding cores=1 - nb forwarding ports=10
> +    RX queues=1 - RX desc=128 - RX free threshold=64
> +    RX threshold registers: pthresh=8 hthresh=8 wthresh=4
> +    TX queues=1 - TX desc=512 - TX free threshold=0
> +    TX threshold registers: pthresh=32 hthresh=8 wthresh=8
> +
> +Configure the traffic generator to send VLAN packets with the Tag
> +Identifier  ``1`` and send 1 packet on port ``A``.
> +
> +Verify that the VLAN packet was correctly received on port ``B`` with VLAN
> tag ``1``.
> +
> +Configure the traffic generator to send VLAN packets with not matched
> +Tag Identifier and send 1 packet on port ``A``.
> +
> +Verify that the VLAN packet was not correctly received on port ``B``
> +with this not matched VLAN Tag.
> 
>  Test Case: Enable receipt of VLAN packets and VLAN header stripping
> ================================================================
> ===
> @@ -89,6 +120,7 @@ Setup the ``mac`` forwarding mode::
>  Enable the receipt of VLAN packets with VLAN Tag Identifier 1 on port 0::
> 
>    testpmd> rx_vlan add 1 0
> +  testpmd> vlan set strip on 0
>    testpmd> start
>      rxonly packet forwarding - CRC stripping disabled - packets/burst=32
>      nb forwarding cores=1 - nb forwarding ports=10 @@ -100,8 +132,7 @@
> Enable the receipt of VLAN packets with VLAN Tag Identifier 1 on port 0::
>  Configure the traffic generator to send VLAN packets with the Tag Identifier
>   ``1`` and send 1 packet on port ``A``.
> 
> -Verify that the VLAN packet was correctly received on port ``B`` with VLAN
> tag ``1``.
> -
> +Verify that the VLAN packet was correctly received on port ``B`` without
> VLAN tag ``1``.
> 
>  Test Case: Disable receipt of VLAN packets
> ==========================================
> --
> 2.14.3