[dts] [PATCH] replace protocal with protocol in all test plans

[Tu, Lijuan]

Applied, thanks

> -----Original Message-----
> From: dts [mailto:dts-bounces at dpdk.org] On Behalf Of Rami Rosen
> Sent: Tuesday, April 30, 2019 3:13 AM
> To: dts at dpdk.org
> Cc: Rami Rosen <ramirose at gmail.com>
> Subject: [dts] [PATCH] replace protocal with protocol in all test plans
> 
> This patch replaces the word "protocal" with "protocol" in all test plans.
> 
> Signed-off-by: Rami Rosen <ramirose at gmail.com>
> ---
>  test_plans/l3fwdacl_test_plan.rst              |  4 ++--
>  test_plans/pmd_bonded_8023ad_test_plan.rst     |  2 +-
>  test_plans/vm2vm_virtio_net_perf_test_plan.rst | 12 ++++++------
>  3 files changed, 9 insertions(+), 9 deletions(-)
> 
> diff --git a/test_plans/l3fwdacl_test_plan.rst
> b/test_plans/l3fwdacl_test_plan.rst
> index 5e5b854..9fd5e50 100644
> --- a/test_plans/l3fwdacl_test_plan.rst
> +++ b/test_plans/l3fwdacl_test_plan.rst
> @@ -136,7 +136,7 @@ Ipv4 packet match destination port 101 will be
> dropped::
>      Send one ipv4 packet with destination port 101 will be dropped.
>      Send one ipv4 packet with destination port 1 will be forwarded to PORT0
> 
> -Ipv4 packet match protocal TCP will be dropped::
> +Ipv4 packet match protocol TCP will be dropped::
> 
>      Add one ACL rule and default route rule in /root/rule_ipv4.db
>      @0.0.0.0/0 0.0.0.0/0 0 : 65535 0 : 65535 6/0xff @@ -231,7 +231,7 @@ Ipv6
> packet match destination port 101 will be dropped::
>      Send one ipv6 packet with destination port 101 will be dropped.
>      Send one ipv6 packet with destination port 1 will be forwarded to PORT0
> 
> -Ipv6 packet match protocal TCP will be dropped::
> +Ipv6 packet match protocol TCP will be dropped::
> 
>      Add one ACL rule and default route rule in /root/rule_ipv6.db
>      @0:0:0:0:0:0:0:0/0 0:0:0:0:0:0:0:0/0 0 : 65535 0 : 65535 6/0xff diff --git
> a/test_plans/pmd_bonded_8023ad_test_plan.rst
> b/test_plans/pmd_bonded_8023ad_test_plan.rst
> index 4e45e08..45a8fca 100644
> --- a/test_plans/pmd_bonded_8023ad_test_plan.rst
> +++ b/test_plans/pmd_bonded_8023ad_test_plan.rst
> @@ -39,7 +39,7 @@ testpmd.
>  link bonding mode 4 is IEEE 802.3ad Dynamic link aggregation. Creates
> aggregation groups that share the same speed and duplex settings. Utilizes
> all  slaves in the active aggregator according to the 802.3ad specification.
> DPDK -realize it based on 802.1AX specification, it includes LACP protocal and
> Marker
> +realize it based on 802.1AX specification, it includes LACP protocol
> +and Marker
>  protocol. This mode requires a switch that supports IEEE 802.3ad Dynamic
> link  aggregation.
> 
> diff --git a/test_plans/vm2vm_virtio_net_perf_test_plan.rst
> b/test_plans/vm2vm_virtio_net_perf_test_plan.rst
> index 6ae4339..a822e49 100644
> --- a/test_plans/vm2vm_virtio_net_perf_test_plan.rst
> +++ b/test_plans/vm2vm_virtio_net_perf_test_plan.rst
> @@ -74,12 +74,12 @@ Test Case 1: vhost-user + virtio-net VM2VM with tcp
> traffic
>       -device virtio-net-
> pci,mac=52:54:00:00:00:02,netdev=mynet2,mrg_rxbuf=on,csum=on,gso=on,g
> uest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on  \
>       -vnc :11 -daemonize
> 
> -3. On VM1, set virtio device IP and run arp protocal::
> +3. On VM1, set virtio device IP and run arp protocol::
> 
>      ifconfig ens3 1.1.1.2
>      arp -s 1.1.1.8 52:54:00:00:00:02
> 
> -4. On VM2, set virtio device IP and run arp protocal::
> +4. On VM2, set virtio device IP and run arp protocol::
> 
>      ifconfig ens3 1.1.1.8
>      arp -s 1.1.1.2 52:54:00:00:00:01
> @@ -124,12 +124,12 @@ Test Case 2: vhost-user + virtio-net VM2VM zero-
> copy with tcp traffic
>       -device virtio-net-
> pci,mac=52:54:00:00:00:02,netdev=mynet2,mrg_rxbuf=on,csum=on,gso=on,g
> uest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on  \
>       -vnc :11 -daemonize
> 
> -3. On VM1, set virtio device IP and run arp protocal::
> +3. On VM1, set virtio device IP and run arp protocol::
> 
>      ifconfig ens3 1.1.1.2
>      arp -s 1.1.1.8 52:54:00:00:00:02
> 
> -4. On VM2, set virtio device IP and run arp protocal::
> +4. On VM2, set virtio device IP and run arp protocol::
> 
>      ifconfig ens3 1.1.1.8
>      arp -s 1.1.1.2 52:54:00:00:00:01
> @@ -174,12 +174,12 @@ Test Case 3: vhost-user + virtio-net VM2VM with
> udp traffic
>       -device virtio-net-
> pci,mac=52:54:00:00:00:02,netdev=mynet2,mrg_rxbuf=on,csum=on,guest_csu
> m=on,host_tso4=on,guest_tso4=on,guest_ecn=on,guest_ufo=on,host_ufo=o
> n \
>       -vnc :11 -daemonize
> 
> -3. On VM1, set virtio device IP and run arp protocal::
> +3. On VM1, set virtio device IP and run arp protocol::
> 
>      ifconfig ens3 1.1.1.2
>      arp -s 1.1.1.8 52:54:00:00:00:02
> 
> -4. On VM2, set virtio device IP and run arp protocal::
> +4. On VM2, set virtio device IP and run arp protocol::
> 
>      ifconfig ens3 1.1.1.8
>      arp -s 1.1.1.2 52:54:00:00:00:01
> --
> 1.8.3.1