[dts] [PATCH]test_plans: add port stop before port reset

[Tu, Lijuan]

Applied, thanks

> -----Original Message-----
> From: dts [mailto:dts-bounces at dpdk.org] On Behalf Of Peng Yuan
> Sent: Monday, March 23, 2020 2:29 PM
> To: dts at dpdk.org
> Cc: Peng, Yuan <yuan.peng at intel.com>
> Subject: [dts] [PATCH]test_plans: add port stop before port reset
> 
> Add port stop before port reset, and add port start after port reset.
> 
> Signed-off-by: Peng Yuan <yuan.peng at intel.com>
> 
> diff --git a/test_plans/vf_pf_reset_test_plan.rst
> b/test_plans/vf_pf_reset_test_plan.rst
> index 51a3e3d..d433d71 100644
> --- a/test_plans/vf_pf_reset_test_plan.rst
> +++ b/test_plans/vf_pf_reset_test_plan.rst
> @@ -128,11 +128,11 @@ Test Case 1: vf reset -- create two vfs on one pf  9.
> Reset the vfs, run the command::
> 
>       testpmd> stop
> -     testpmd> port reset 0
> -     testpmd> port reset 1
> +     testpmd> port stop all
> +     testpmd> port reset all
> +     testpmd> port start all
>       testpmd> start
> 
> -   or just run the command "port reset all".
>     Send the same 1000 packets with scapy from tester, verify the packets can
> be
>     received by one VF and can be forward to another VF correctly,
>     check the port info::
> @@ -269,7 +269,9 @@ Test Case 4: vlan rx restore -- vf reset all ports  4.
> Reset both vfs::
> 
>       testpmd> stop
> +     testpmd> port stop all
>       testpmd> port reset all
> +     testpmd> port start all
>       testpmd> start
> 
>     Send the packets in step2 from tester, @@ -313,7 +315,9 @@ test Case 5:
> vlan rx restore -- vf reset one port  3. Pf reset, then reset vf0, send packets
> from tester::
> 
>       testpmd> stop
> +     testpmd> port stop 0
>       testpmd> port reset 0
> +     testpmd> port start 0
>       testpmd> start
>       sendp([Ether(dst="00:11:22:33:44:11")/IP()/Raw('x'*1000)], \
>       iface="ens3f0",count=1000)
> @@ -333,7 +337,9 @@ test Case 5: vlan rx restore -- vf reset one port  4.
> Reset vf1::
> 
>       testpmd> stop
> +     testpmd> port stop 1
>       testpmd> port reset 1
> +     testpmd> port start 1
>       testpmd> start
>       sendp([Ether(dst="00:11:22:33:44:11")/IP()/Raw('x'*1000)], \
>       iface="ens3f0",count=1000)
> @@ -400,7 +406,9 @@ Test Case 6: vlan rx restore -- create one vf on each
> pf  4. Reset both vfs, send packets from tester::
> 
>       testpmd> stop
> +     testpmd> port stop all
>       testpmd> port reset all
> +     testpmd> port start all
>       testpmd> start
>       sendp([Ether(dst="00:11:22:33:44:11")/IP()/Raw('x'*1000)], \
>       iface="ens3f0",count=1000)
> --
> 2.7.4