[dpdk-stable] [dpdk-dev] [PATCH v2 06/10] net/virtio: fix queue setup consistency
Tiwei Bie
tiwei.bie at intel.com
Fri Dec 8 03:17:44 CET 2017
Hi Olivier,
On Thu, Dec 07, 2017 at 03:14:44PM +0100, Olivier MATZ wrote:
> On Wed, Dec 06, 2017 at 01:25:29PM +0800, Tiwei Bie wrote:
> > Hi Maxime and Olivier:
> >
> > On Thu, Sep 07, 2017 at 02:13:43PM +0200, Olivier Matz wrote:
> > [...]
> > > diff --git a/drivers/net/virtio/virtio_ethdev.c b/drivers/net/virtio/virtio_ethdev.c
> > > index 8eee3ff80..c7888f103 100644
> > > --- a/drivers/net/virtio/virtio_ethdev.c
> > > +++ b/drivers/net/virtio/virtio_ethdev.c
> > > @@ -1737,6 +1737,19 @@ virtio_dev_start(struct rte_eth_dev *dev)
> > > struct virtnet_rx *rxvq;
> > > struct virtnet_tx *txvq __rte_unused;
> > > struct virtio_hw *hw = dev->data->dev_private;
> > > + int ret;
> > > +
> > > + /* Finish the initialization of the queues */
> > > + for (i = 0; i < dev->data->nb_rx_queues; i++) {
> > > + ret = virtio_dev_rx_queue_setup_finish(dev, i);
> > > + if (ret < 0)
> > > + return ret;
> > > + }
> >
> > I'm trying to fix an issue [1] reported by Antonio. And during
> > the debugging, I found that vector Rx of virtio PMD has been
> > broken (when doing port stop/start) since below two patches were
> > applied:
> >
> > 25bf7a0b0936 ("vhost: make error handling consistent in Rx path")
> > -- needed on the Tx side (testpmd/vhost-pmd in below test)
> > efc83a1e7fc3 ("net/virtio: fix queue setup consistency")
> > -- needed on the Rx side (testpmd/virtio-user in below test)
>
> Just to be sure I understand properly: each of these 2 patches
> break a different part your test case?
>
Thank you for looking into this! ;-)
I mean the above test case won't pass when we have both
of them applied. And the first patch changes the Tx side,
and the second one changes the Rx side.
I haven't done thorough analysis on the first patch, so
I'm not sure what would be affected in the non-mergeable
Rx and vector Rx of virtio-PMD after changing the error
handling in vhost.
But I think there is something wrong with this patch (i.e.
the second patch). From my understanding, it seems that
virtio_rxq_rearm_vec() has an assumption that each time
it's called, the starting 'desc_idx' should be multiple
times of RTE_VIRTIO_VPMD_RX_REARM_THRESH (or 0). After
introducing virtio_dev_rx_queue_setup_finish() in device
start, the rxq will be fully refilled no matter where
the 'desc_idx' is after a device stop/start. And it could
break such assumption.
> I tried to reproduce your test case (the working case first):
> - on 0c4f909c17 (the commit before the efc83a1e7fc3)
> - without the patch disabling mergeable Rx
>
> No packet is received. Am I doing something wrong? Please see the
> log:
>
> cd /root/dpdk.org
> git checkout -b test 0c4f909c17
> rm -rf build && make config T=x86_64-native-linuxapp-gcc && make -j32
> insmod build/kmod/igb_uio.ko
> echo 1000 > /sys/devices/system/node/node0/hugepages/hugepages-2048kB/nr_hugepages
> echo 1000 > /sys/devices/system/node/node1/hugepages/hugepages-2048kB/nr_hugepages
Sorry, I forgot to mention that, 1G hugepage is required
to use virtio-user (2M hugepage won't work). For more
details about it, you could refer to the "Limitations"
section in below doc:
http://dpdk.org/doc/guides/howto/virtio_user_for_container_networking.html#limitations
Best regards,
Tiwei Bie
More information about the stable
mailing list