[dpdk-stable] [dpdk-dev] [PATCH v2] net/ixgbe: enable 10Mb/s link setup for x553

[Zhao1, Wei]

> -----Original Message-----
> From: Stillwell Jr, Paul M
> Sent: Saturday, March 30, 2019 2:47 AM
> To: Zhao1, Wei <wei.zhao1 at intel.com>; dev at dpdk.org
> Cc: Lu, Wenzhuo <wenzhuo.lu at intel.com>; stable at dpdk.org; Zhang, Qi Z
> <qi.z.zhang at intel.com>; Zhao1, Wei <wei.zhao1 at intel.com>
> Subject: RE: [dpdk-dev] [PATCH v2] net/ixgbe: enable 10Mb/s link setup for
> x553
> 
> 
> > -----Original Message-----
> > From: dev <dev-bounces at dpdk.org> On Behalf Of Wei Zhao
> > Sent: Friday, March 29, 2019 1:16 AM
> > To: dev at dpdk.org
> > Cc: Lu, Wenzhuo <wenzhuo.lu at intel.com>; stable at dpdk.org; Zhang, Qi Z
> > <qi.z.zhang at intel.com>; Zhao1, Wei <wei.zhao1 at intel.com>
> > Subject: [dpdk-dev] [PATCH v2] net/ixgbe: enable 10Mb/s link setup for
> > x553
> >
> > There is need to eanble 10Mb/s link foixgbe NIC of x553.
> 
> Couple of typos, how about:
> 
> Enable 10Mb/s link for ixgbe x553.


Good,  update in v2

> 
> > This new device has own device id of 0x15E4 and 0x15E5, so ixgbe PMD
> > driver need to special check when setup link for these two types of device.
> >
> > Signed-off-by: Wei Zhao <wei.zhao1 at intel.com>
> >
> > ---
> >
> > v2:
> > delete test code and change permit link speed
> > ---
> >  drivers/net/ixgbe/ixgbe_ethdev.c | 12 +++++++++++-
> >  1 file changed, 11 insertions(+), 1 deletion(-)
> >
> > diff --git a/drivers/net/ixgbe/ixgbe_ethdev.c
> > b/drivers/net/ixgbe/ixgbe_ethdev.c
> > index 97e1021..0aef577 100644
> > --- a/drivers/net/ixgbe/ixgbe_ethdev.c
> > +++ b/drivers/net/ixgbe/ixgbe_ethdev.c
> > @@ -2701,6 +2701,10 @@ static int eth_ixgbevf_pci_remove(struct
> > rte_pci_device *pci_dev)
> >  		allowed_speeds = ETH_LINK_SPEED_100M |
> ETH_LINK_SPEED_1G |
> >  			ETH_LINK_SPEED_2_5G |  ETH_LINK_SPEED_5G |
> >  			ETH_LINK_SPEED_10G;
> > +		if (hw->device_id == IXGBE_DEV_ID_X550EM_A_1G_T ||
> > +				hw->device_id ==
> > IXGBE_DEV_ID_X550EM_A_1G_T_L)
> > +			allowed_speeds = ETH_LINK_SPEED_10M |
> > +				ETH_LINK_SPEED_100M |
> > ETH_LINK_SPEED_1G;
> >  		break;
> >  	default:
> >  		allowed_speeds = ETH_LINK_SPEED_100M |
> ETH_LINK_SPEED_1G | @@
> > -2742,6 +2746,8 @@ static int eth_ixgbevf_pci_remove(struct
> > rte_pci_device *pci_dev)
> >  			speed |= IXGBE_LINK_SPEED_1GB_FULL;
> >  		if (*link_speeds & ETH_LINK_SPEED_100M)
> >  			speed |= IXGBE_LINK_SPEED_100_FULL;
> > +		if (*link_speeds & ETH_LINK_SPEED_10M)
> > +			speed |= IXGBE_LINK_SPEED_10_FULL;
> >  	}
> >
> >  	err = ixgbe_setup_link(hw, speed, link_up); @@ -4061,8 +4067,12
> @@
> > static int ixgbevf_dev_xstats_get_names(__rte_unused struct
> > rte_eth_dev *dev,
> >  	switch (link_speed) {
> >  	default:
> >  	case IXGBE_LINK_SPEED_UNKNOWN:
> > +		if (hw->device_id == IXGBE_DEV_ID_X550EM_A_1G_T ||
> > +			hw->device_id ==
> > IXGBE_DEV_ID_X550EM_A_1G_T_L)
> > +			link.link_speed = ETH_SPEED_NUM_10M;
> > +		else
> > +			link.link_speed = ETH_SPEED_NUM_100M;
> >  		link.link_duplex = ETH_LINK_FULL_DUPLEX;
> > -		link.link_speed = ETH_SPEED_NUM_100M;
> >  		break;
> >
> >  	case IXGBE_LINK_SPEED_100_FULL:
> > --
> > 1.8.3.1