[PATCH v5] vdpa/ifc/base: wait for queue disable before saving q-state
Xia, Chenbo
chenbo.xia at intel.com
Fri Nov 4 03:31:54 CET 2022
> -----Original Message-----
> From: Maheshwari, Abhishek <abhishek.maheshwari at intel.com>
> Sent: Thursday, November 3, 2022 5:35 PM
> To: maxime.coquelin at redhat.com; Wang, Xiao W <xiao.w.wang at intel.com>
> Cc: dev at dpdk.org; stable at dpdk.org; Xia, Chenbo <chenbo.xia at intel.com>;
> Mandal, Purna Chandra <purna.chandra.mandal at intel.com>; Maheshwari,
> Abhishek <abhishek.maheshwari at intel.com>
> Subject: [PATCH v5] vdpa/ifc/base: wait for queue disable before saving q-
> state
>
> Some ifc hardware require synchronization between disabling a queue and
> saving queue-state from LM registers. When queue is disabled from vDPA
> driver, ifc device stops executing new virtio-cmds and then updates LM
> registers with used/avail index. Before saving the queue-state, vDPA
> driver should wait until the queue is disabled from backend.
>
> Fixes: 5d75517beffe ("vdpa/ifc/base: access block device registers")
>
Will remove above blank line and add Andy's A-By when applying
For this patch:
Reviewed-by: Chenbo Xia <chenbo.xia at intel.com>
> Cc: stable at dpdk.org
>
> Signed-off-by: Abhishek Maheshwari <abhishek.maheshwari at intel.com>
>
> ---
> v2:
> * Fixing the styling issues
> * Addressing comment to avoid reading the register again after
> exhausting the tries
>
> v3:
> * Fixing warning condition
>
> v4:
> * Fixing print argument format to %u in warning
>
> v5:
> * Addressing comments based on input that line length limit is 100
> ---
> drivers/vdpa/ifc/base/ifcvf.c | 15 +++++++++++++++
> 1 file changed, 15 insertions(+)
>
> diff --git a/drivers/vdpa/ifc/base/ifcvf.c b/drivers/vdpa/ifc/base/ifcvf.c
> index f1e1474447..60555a6786 100644
> --- a/drivers/vdpa/ifc/base/ifcvf.c
> +++ b/drivers/vdpa/ifc/base/ifcvf.c
> @@ -257,6 +257,7 @@ ifcvf_hw_disable(struct ifcvf_hw *hw)
> u32 i;
> struct ifcvf_pci_common_cfg *cfg;
> u32 ring_state;
> + int q_disable_try;
>
> cfg = hw->common_cfg;
> if (!cfg) {
> @@ -275,6 +276,20 @@ ifcvf_hw_disable(struct ifcvf_hw *hw)
> continue;
> }
>
> + /* Some ifc hardware require synchronization between disabling
> a
> + * queue and saving queue-state from LM registers. When queue
> is
> + * disabled from vDPA driver, ifc device stops executing new
> + * virtio-cmds and then updates LM registers with used/avail
> + * index. Before saving the queue-state, vDPA driver waits
> until
> + * the queue is disabled from backend.
> + */
> + q_disable_try = 10;
> + while (q_disable_try-- && IFCVF_READ_REG16(&cfg->queue_enable))
> + msec_delay(10);
> +
> + if (!q_disable_try)
> + WARNINGOUT("Failed to disable Q:%u, Saved state could be
> invalid\n", i);
> +
> if (hw->device_type == IFCVF_BLK)
> ring_state = *(u32 *)(hw->lm_cfg +
> IFCVF_LM_RING_STATE_OFFSET +
> --
> 2.31.1
More information about the stable
mailing list