[dpdk-users] DPDK Problem Binding to Network Port
Thomas Lazor
tjlazor at vt.edu
Fri May 20 23:57:04 CEST 2016
Hi,
I am running into a problem when I bind the igb_uio driver to the network
card. I am using dpdk 16.04 and my kernel version is 3.2.14.
Using the setup script, I compiled the target library, inserted the igb_uio
module, set up hugepages, and bound the igb_uio driver.
$ ./tools/dpdk_nic_bind.py --status
Network devices using DPDK-compatible driver
============================================
0000:01:00.0 '82599ES 10-Gigabit SFI/SFP+ Network Connection' drv=igb_uio
unused=uio_pci_generic
Network devices using kernel driver
===================================
0000:01:00.1 '82599ES 10-Gigabit SFI/SFP+ Network Connection' if=eth4
drv=ixgbe unused=igb_uio,uio_pci_generic
0000:06:00.0 'I350 Gigabit Network Connection' if=eth0 drv=igb
unused=igb_uio,uio_pci_generic *Active*
0000:06:00.1 'I350 Gigabit Network Connection' if=eth1 drv=igb
unused=igb_uio,uio_pci_generic
Other network devices
=====================
<none>
However, when I run ifconfig -a, I can no longer see the network card:
$ ifconfig -a
eth0 Link encap:Ethernet HWaddr 00:25:90:E1:83:24
inet addr:10.1.1.42 Bcast:10.1.1.255 Mask:255.255.255.0
inet6 addr: fe80::225:90ff:fee1:8324/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:7634 errors:0 dropped:72 overruns:0 frame:0
TX packets:4978 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:1051991 (1.0 MiB) TX bytes:732247 (715.0 KiB)
Memory:dfd20000-dfd40000
eth1 Link encap:Ethernet HWaddr 00:25:90:E1:83:25
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Memory:dfd00000-dfd20000
eth4 Link encap:Ethernet HWaddr 00:1B:21:A6:15:A1
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:54 errors:0 dropped:0 overruns:0 frame:0
TX packets:54 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:3552 (3.4 KiB) TX bytes:3552 (3.4 KiB)
mic0 Link encap:Ethernet HWaddr 4C:79:BA:30:01:59
inet addr:172.31.1.254 Bcast:172.31.1.255 Mask:255.255.255.0
inet6 addr: fe80::4e79:baff:fe30:159/64 Scope:Link
UP BROADCAST RUNNING MTU:64512 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Why is this? I believe I should see a dpdk0 card when it is bound. When I
unbind the card, it does show up if I run ifconfig.
Many thanks,
Thomas
More information about the users
mailing list