net/cxgbe: fix init failure due to new flash parts

diff --git a/drivers/net/cxgbe/base/t4_hw.c b/drivers/net/cxgbe/base/t4_hw.c
index 628b280ef..31762c9c5 100644
--- a/drivers/net/cxgbe/base/t4_hw.c
+++ b/drivers/net/cxgbe/base/t4_hw.c
@@ -4681,9 +4681,8 @@  struct flash_desc {
 int t4_get_flash_params(struct adapter *adapter)
 {
 	/*
-	 * Table for non-Numonix supported flash parts.  Numonix parts are left
-	 * to the preexisting well-tested code.  All flash parts have 64KB
-	 * sectors.
+	 * Table for non-standard supported Flash parts.  Note, all Flash
+	 * parts must have 64KB sectors.
 	 */
 	static struct flash_desc supported_flash[] = {
 		{ 0x00150201, 4 << 20 },       /* Spansion 4MB S25FL032P */
@@ -4692,7 +4691,7 @@  int t4_get_flash_params(struct adapter *adapter)
 	int ret;
 	u32 flashid = 0;
 	unsigned int part, manufacturer;
-	unsigned int density, size;
+	unsigned int density, size = 0;
 
 	/**
 	 * Issue a Read ID Command to the Flash part.  We decode supported
@@ -4707,6 +4706,9 @@  int t4_get_flash_params(struct adapter *adapter)
 	if (ret < 0)
 		return ret;
 
+	/**
+	 * Check to see if it's one of our non-standard supported Flash parts.
+	 */
 	for (part = 0; part < ARRAY_SIZE(supported_flash); part++) {
 		if (supported_flash[part].vendor_and_model_id == flashid) {
 			adapter->params.sf_size =
@@ -4717,6 +4719,15 @@  int t4_get_flash_params(struct adapter *adapter)
 		}
 	}
 
+	/**
+	 * Decode Flash part size.  The code below looks repetative with
+	 * common encodings, but that's not guaranteed in the JEDEC
+	 * specification for the Read JADEC ID command.  The only thing that
+	 * we're guaranteed by the JADEC specification is where the
+	 * Manufacturer ID is in the returned result.  After that each
+	 * Manufacturer ~could~ encode things completely differently.
+	 * Note, all Flash parts must have 64KB sectors.
+	 */
 	manufacturer = flashid & 0xff;
 	switch (manufacturer) {
 	case 0x20: { /* Micron/Numonix */
@@ -4753,20 +4764,80 @@  int t4_get_flash_params(struct adapter *adapter)
 		case 0x22:
 			size = 1 << 28; /* 256MB */
 			break;
-		default:
-			dev_err(adapter, "Micron Flash Part has bad size, ID = %#x, Density code = %#x\n",
-				flashid, density);
-			return -EINVAL;
 		}
+		break;
+	}
 
-		adapter->params.sf_size = size;
-		adapter->params.sf_nsec = size / SF_SEC_SIZE;
+	case 0x9d: { /* ISSI -- Integrated Silicon Solution, Inc. */
+		/**
+		 * This Density -> Size decoding table is taken from ISSI
+		 * Data Sheets.
+		 */
+		density = (flashid >> 16) & 0xff;
+		switch (density) {
+		case 0x16:
+			size = 1 << 25; /* 32MB */
+			break;
+		case 0x17:
+			size = 1 << 26; /* 64MB */
+			break;
+		}
 		break;
 	}
-	default:
-		dev_err(adapter, "Unsupported Flash Part, ID = %#x\n", flashid);
-		return -EINVAL;
+
+	case 0xc2: { /* Macronix */
+		/**
+		 * This Density -> Size decoding table is taken from Macronix
+		 * Data Sheets.
+		 */
+		density = (flashid >> 16) & 0xff;
+		switch (density) {
+		case 0x17:
+			size = 1 << 23; /* 8MB */
+			break;
+		case 0x18:
+			size = 1 << 24; /* 16MB */
+			break;
+		}
+		break;
+	}
+
+	case 0xef: { /* Winbond */
+		/**
+		 * This Density -> Size decoding table is taken from Winbond
+		 * Data Sheets.
+		 */
+		density = (flashid >> 16) & 0xff;
+		switch (density) {
+		case 0x17:
+			size = 1 << 23; /* 8MB */
+			break;
+		case 0x18:
+			size = 1 << 24; /* 16MB */
+			break;
+		}
+		break;
 	}
+	}
+
+	/* If we didn't recognize the FLASH part, that's no real issue: the
+	 * Hardware/Software contract says that Hardware will _*ALWAYS*_
+	 * use a FLASH part which is at least 4MB in size and has 64KB
+	 * sectors.  The unrecognized FLASH part is likely to be much larger
+	 * than 4MB, but that's all we really need.
+	 */
+	if (size == 0) {
+		dev_warn(adapter,
+			 "Unknown Flash Part, ID = %#x, assuming 4MB\n",
+			 flashid);
+		size = 1 << 22;
+	}
+
+	/**
+	 * Store decoded Flash size and fall through into vetting code.
+	 */
+	adapter->params.sf_size = size;
+	adapter->params.sf_nsec = size / SF_SEC_SIZE;
 
 found:
 	/*