[v1,03/13] doc: add guide for ppfe net PMD
Checks
Commit Message
This patch add documentation for ppfe network
poll mode driver.
PPFE is a hardware programmable packet
forwarding engine to provide high performance
ethernet interfaces.
Signed-off-by: Gagandeep Singh <g.singh@nxp.com>
Acked-by: Nipun Gupta <nipun.gupta@nxp.com>
Acked-by: Akhil Goyal <akhil.goyal@nxp.com>
---
MAINTAINERS | 1 +
doc/guides/nics/features/ppfe.ini | 1 +
doc/guides/nics/index.rst | 1 +
doc/guides/nics/ppfe.rst | 168 ++++++++++++++++++++++++++++++
4 files changed, 171 insertions(+)
create mode 100644 doc/guides/nics/ppfe.rst
@@ -784,6 +784,7 @@ F: doc/guides/nics/features/enetc.ini
NXP ppfe
M: Gagandeep Singh <g.singh@nxp.com>
M: Akhil Goyal <akhil.goyal@nxp.com>
+F: doc/guides/nics/ppfe.rst
F: drivers/net/ppfe/
F: doc/guides/nics/features/ppfe.ini
@@ -6,3 +6,4 @@
[Features]
Linux VFIO = Y
ARMv8 = Y
+Usage doc = Y
@@ -47,6 +47,7 @@ Network Interface Controller Drivers
nfp
octeontx
octeontx2
+ ppfe
qede
sfc_efx
softnic
new file mode 100644
@@ -0,0 +1,168 @@
+.. SPDX-License-Identifier: BSD-3-Clause
+ Copyright 2019 NXP
+
+PPFE Poll Mode Driver
+======================
+
+The PPFE NIC PMD (**librte_pmd_ppfe**) provides poll mode driver
+support for the inbuilt NIC found in the **NXP LS1012** SoC.
+
+More information can be found at `NXP Official Website
+<https://nxp.com/ls1012a>`_.
+
+PPFE
+-----
+
+This section provides an overview of the NXP PPFE
+and how it is integrated into the DPDK.
+
+Contents summary
+
+- PPFE overview
+- PPFE features
+- Supported PPFE SoCs
+- Prerequisites
+- Driver compilation and testing
+- Limitations
+
+PPFE Overview
+~~~~~~~~~~~~~~
+
+PPFE is a hardware programmable packet forwarding engine to provide
+high performance Ethernet interfaces. The diagram below shows a
+system level overview of PPFE:
+
+.. code-block:: console
+
+ ====================================================+===============
+ US +-----------------------------------------+ | Kernel Space
+ | | |
+ | PPFE Ethernet Driver | |
+ +-----------------------------------------+ |
+ ^ | ^ | |
+ PPFE RXQ| |TXQ RXQ| |TXQ |
+ PMD | | | | |
+ | v | v | +----------+
+ +---------+ +----------+ | | pfe.ko |
+ | pfe_eth0| | pfe_eth1 | | +----------+
+ +---------+ +----------+ |
+ ^ | ^ | |
+ TXQ| |RXQ TXQ| |RXQ |
+ | | | | |
+ | v | v |
+ +------------------------+ |
+ | | |
+ | PPFE HIF driver | |
+ +------------------------+ |
+ ^ | |
+ RX | TX | |
+ RING| RING| |
+ | v |
+ +--------------+ |
+ | | |
+ ==================| HIF |==================+===============
+ +-----------+ +--------------+
+ | | | | HW
+ | PPFE +--------------+ |
+ | +-----+ +-----+ |
+ | | MAC | | MAC | |
+ | | | | | |
+ +-------+-----+----------------+-----+----+
+ | PHY | | PHY |
+ +-----+ +-----+
+
+
+The HIF, PPFE, MAC and PHY are the hardware blocks, the pfe.ko is a kernel
+module, the PPFE HIF driver and the PPFE ethernet driver combined represent
+as DPDK PPFE poll mode driver are running in the userspace.
+
+The PPFE hardware supports one HIF (host interface) RX ring and one TX ring
+to send and receive packets through packet forwarding engine. Both network
+interface traffic is multiplexed and send over HIF queue.
+
+pfe_eth0 and pfe_eth1 are logical ethernet interfaces, created by HIF client
+driver. HIF driver is responsible for send and receive packets between
+host interface and these logical interfaces. PPFE ethernet driver is a
+hardware independent and register with the HIF client driver to transmit and
+receive packets from HIF via logical interfaces.
+
+pfe.ko is required for PHY initialisation.
+
+PPFE Features
+~~~~~~~~~~~~~~
+
+- ARMv8
+
+Supported PPFE SoCs
+~~~~~~~~~~~~~~~~~~~~
+
+- LS1012
+
+Prerequisites
+~~~~~~~~~~~~~
+
+Below are some pre-requisites for executing PPFE PMD on a PPFE
+compatible board:
+
+1. **ARM 64 Tool Chain**
+
+ For example, the `*aarch64* Linaro Toolchain <https://releases.linaro.org/components/toolchain/binaries/7.3-2018.05/aarch64-linux-gnu/gcc-linaro-7.3.1-2018.05-i686_aarch64-linux-gnu.tar.xz>`_.
+
+2. **Linux Kernel**
+
+ It can be obtained from `NXP's Github hosting <https://source.codeaurora.org/external/qoriq/qoriq-components/linux>`_.
+
+3. **Rootfile system**
+
+ Any *aarch64* supporting filesystem can be used. For example,
+ Ubuntu 16.04 LTS (Xenial) or 18.04 (Bionic) userland which can be obtained
+ from `here <http://cdimage.ubuntu.com/ubuntu-base/releases/18.04/release/ubuntu-base-18.04.1-base-arm64.tar.gz>`_.
+
+4. The ethernet device will be registered as virtual device, so ppfe has dependency on
+ **rte_bus_vdev** library and it is mandatory to use `--vdev` with value `eth_pfe` to
+ run DPDK application.
+
+The following dependencies are not part of DPDK and must be installed
+separately:
+
+- **NXP Linux LSDK**
+
+ NXP Layerscape software development kit (LSDK) includes support for family
+ of QorIQ® ARM-Architecture-based system on chip (SoC) processors
+ and corresponding boards.
+
+ It includes the Linux board support packages (BSPs) for NXP SoCs,
+ a fully operational tool chain, kernel and board specific modules.
+
+ LSDK and related information can be obtained from: `LSDK <https://www.nxp.com/support/developer-resources/run-time-software/linux-software-and-development-tools/layerscape-software-development-kit:LAYERSCAPE-SDK>`_
+
+- **pfe kernel module**
+
+ pfe kernel module can be obtained from NXP Layerscape software development kit at
+ location `/lib/modules/<kernel version>/kernel/drivers/staging/fsl_ppfe` in rootfs.
+ Module should be loaded using below command:
+
+ .. code-block:: console
+
+ insmod pfe.ko us=1
+
+
+Driver compilation and testing
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Follow instructions available in the document
+:ref:`compiling and testing a PMD for a NIC <pmd_build_and_test>`
+to launch **testpmd**
+
+Additionally, PPFE driver need `--vdev` as an input with value `eth_pfe` to execute DPDK application,
+see the command below:
+
+ .. code-block:: console
+
+ <dpdk app> <EAL args> --vdev="eth_pfe0" --vdev="eth_pfe1" -- ...
+
+
+Limitations
+~~~~~~~~~~~
+
+- Multi buffer pool cannot be supported.