[dpdk-dev] [PATCH] doc: update failsafe feature list

[Ferruh Yigit]

On 9/19/2017 12:39 PM, Matan Azrad wrote:
> Hi Ferruh
> 
>> -----Original Message-----
>> From: Ferruh Yigit [mailto:ferruh.yigit at intel.com]
>> Sent: Tuesday, September 19, 2017 2:00 PM
>> To: Matan Azrad <matan at mellanox.com>; Gaetan Rivet
>> <gaetan.rivet at 6wind.com>
>> Cc: dev at dpdk.org; john.mcnamara at intel.com
>> Subject: Re: [dpdk-dev] [PATCH] doc: update failsafe feature list
>>
>> On 9/19/2017 11:04 AM, Matan Azrad wrote:
>>>
>>> Hi Ferruh
>>>
>>>> -----Original Message-----
>>>> From: Ferruh Yigit [mailto:ferruh.yigit at intel.com]
>>>> Sent: Tuesday, September 19, 2017 12:27 PM
>>>> To: Matan Azrad <matan at mellanox.com>; Gaetan Rivet
>>>> <gaetan.rivet at 6wind.com>
>>>> Cc: dev at dpdk.org
>>>> Subject: Re: [dpdk-dev] [PATCH] doc: update failsafe feature list
>>>>
>>>> On 9/14/2017 4:32 PM, Matan Azrad wrote:
>>>>> Add supported failsafe features to feature list.
>>>>> Remove stats per queue feature from failsafe feature list since
>>>>> queue_stats_mapping_set dev op has not implemented yet.
>>>>>
>>>>> Signed-off-by: Matan Azrad <matan at mellanox.com>
>>>>> ---
>>>>>  doc/guides/nics/features/failsafe.ini | 15 ++++++++++++++-
>>>>>  1 file changed, 14 insertions(+), 1 deletion(-)
>>>>>
>>>>> diff --git a/doc/guides/nics/features/failsafe.ini
>>>>> b/doc/guides/nics/features/failsafe.ini
>>>>> index a42e344..9f48455 100644
>>>>> --- a/doc/guides/nics/features/failsafe.ini
>>>>> +++ b/doc/guides/nics/features/failsafe.ini
>>>>> @@ -4,20 +4,33 @@
>>>>>  ; Refer to default.ini for the full list of available PMD features.
>>>>>  ;
>>>>>  [Features]
>>>>> +Speed capabilities   = Y
>>>>>  Link status          = Y
>>>>>  Link status event    = Y
>>>>>  MTU update           = Y
>>>>>  Jumbo frame          = Y
>>>>> +Scattered Rx         = Y
>>>>> +LRO                  = Y
>>>>> +TSO                  = Y
>>>>>  Promiscuous mode     = Y
>>>>>  Allmulticast mode    = Y
>>>>>  Unicast MAC filter   = Y
>>>>>  Multicast MAC filter = Y
>>>>>  VLAN filter          = Y
>>>>> +Ethertype filter     = Y
>>>>> +N-tuple filter       = Y
>>>>> +SYN filter           = Y
>>>>> +Tunnel filter        = Y
>>>>> +Flexible filter      = Y
>>>>> +Hash filter          = Y
>>>>> +Flow director        = Y
>>>>>  Flow control         = Y
>>>>>  Flow API             = Y
>>>>> +QinQ offload         = Y
>>>>> +L3 checksum offload  = Y
>>>>> +L4 checksum offload  = Y
>>>>>  Packet type parsing  = Y
>>>>>  Basic stats          = Y
>>>>> -Stats per queue      = Y
>>>>>  ARMv7                = Y
>>>>>  ARMv8                = Y
>>>>>  Power8               = Y
>>>>
>>>> I am not sure if claiming support for these features is correct.
>>>> Failsafe itself doesn't provide these features, but relies underlying
>>>> hardware which we don't really know what they supports or not in this
>> stage.
>>>>
>>>
>>> Don't you think that almost all failsafe features rely underlying hardware or
>> sub PMDs?
>>
>> You are right, perhaps we should remove all. This is helpful to show what
>> device features are supported. For failsafe, is this information useful?
>>
> Since there are features that failsafe cannot support without any sub PMD dependences
> (for example "Stats per queue") it is useful.

Sorry, I missed your point.

Device feature list documentation is good for:
- End user can easily see what to expect from a device/driver.
- To trace what features implemented for a device.
- To find out which device has a specific desired feature.

For failsafe, it is a virtual overlay device on other physical devices.

The supported architectures and provided documents features can be
useful. But why/how NIC related features can be useful since all they
are coming form underlay devices?

> 
>>>
>>>> OK for dropping "Stats per queue"
>>>>
>>>>>
>>>
>